Rapid Fire Products

PLAT HUSQVARNA MAUSER LARGE RING #1 BC WALNUT SATIN FINISH BOYDS PAD LASER PANEL PILLAR BEDDING ATTENTION CUSTOMERS: RUN IN FINISH ON BACK SIDE OF BUTT Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERT REM 700 ADL LA FBC NUTMEG SATIN FINISH PACHMAYR PAD LASER PANEL PILLAR BEDDING LOP 13 1/2" ATTENTION CUSTOMERS: BLACK STAIN FROM LASER IN THE BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Long Action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

RH RUGER 1022 CARBINE BARREL CHANNEL WALNUT SATIN FINISH BOYDS PAD LOP 13 1/4" ATTENTION CUSTOMERS: UNEVEN SANDING ON GRIP, FLUTE OF NECK IS VERY SHARP EDGES, OVERSANDING ON ONE SIDE OF THE TIP Barrel Dimensions: Point A = 59/64" and Point B = 43/64"Center to Center of Action Screws: N/AOver All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon installed and is designed for the Factory Ruger 10/22 Semi-Auto Action, measuring 6 3/16" long.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA SAV 111 SIDE RELEASE DBM LONG ACTION FBC FOREST CAMO SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

PH SAV B-SERIES BBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: where barrel meets receiver/Point A=.8" Barrel Dimensions: 9 inches in front of Point A/Point B= .8" Center to Center of Action Screws: 3.35" Over All Length of Part: 31.5" This Inlet will work for both long rifle and magnum action. Attention Customers: We provide the washer for the front take down screw and a trigger guard. Attention Customers: It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

RIMFIRE HUNTER, RUGER 77/22®, FACTORY BARREL CHANNEL PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: WOOD KNOT NEAR TOE AREA OF STOCK, PRESENT IN PHOTO Barrel Dimensions: Point A = 15/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2"Width of Magazine Well: 1 5/16"Length of Magazine Well: 3 11/32" Over All Length of Part: 29" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 Bolt Action 22 Long Rifle. Early plastic stocks will require additional mounting hardware to use our stocks. Please contact Ruger or Brownells (800) 741-0015 for the metal trigger guard and clip assembly. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect>. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLA WIN 70 SA 1PC FP FBC POST 64 COYOTE SATIN FINISH PACHMAYR PAD LASER PANEL ATTENTION CUSTOMERS: LIGHTER COLOR LAMINATE LAYER DID NOT ACCEPT STAIN AS MUCH AS DARKER LAMINATE LAYER. THIS IS NORMAL FOR NATURAL WOOD PRODUCTS. GRIP OF LASER PANEL PRESENT IN PHOTO Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All Rapid Fire sales are final!

HERT HOWA 1500 MINI DBM LH STK RH ACT HVY #6 BC WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.095" and Point B = .783" Center to Center of Action Screws: 6.785" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

LH PH SAV A22 MAGNUM SEMI-AUTO DBM LH STK RH ACT FBC WALNUT SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable and nonrefundable.

CLA REM 770 LONG ACTION FBC NUTMEG SATIN FINISH LIMBSAVER PAD LASER PANEL Barrel Dimensions:where barrel meets receiver/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 different types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

FT RUGER M77 MKII HAWKEYE SHORT ACTION FACTORY BARREL CHANNEL PEPPER HIGH GLOSS PACHMAYR PAD PILLAR BEDDING LASER INITIALS: "SAW" FONT #5 LOP 14" Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH FT SAV 220 SLUG GUN LONG ACTION DBM LEFT HAND STOCK RIGHT HAND ACTION FBC NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/32" and Point B = 55/64" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: This is for the older style floor plate that measures 5.7875. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock. This stock is designed for the right hand bolt action only. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect . All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH SAV B-MAG SHORT ACTION DBM FBC FOREST CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 55/64" and Point B = 39/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS:  To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT SAV 10 TBR BLIND MAGAZINE, SHORT ACTION, CENTERFEED, FACTORY BARREL CHANNEL APPLE JACK SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefunable & nonreturnable.

HERT REM 710 LONG ACTION DBM FBC FOREST CAMO HIGH GLOSS BOYDS PAD LASER PANEL BLACK TIP LOP 13" ATTENTION CUSTOMERS: WHITE PAINT IN BLACK STAIN OF LASER PANEL ON FOREND, PRESENT IN PHOTO. Barrel Dimensions:where barrel meets receiver/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 different types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH FT REM 700 BDL LA LH STOC RH ACT BULL BARREL CHANNEL Coyote Satin Finish Boyds Pad Barrel Dimensions: Point A = 1.245" and Point B = 0.9"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT REM 770 LONG ACTION FBC FOREST CAMO SATIN FINISH BOYDS PAD LASER SYMBOL: EAGLE HEAD Barrel Dimensions:where barrel meets receiver/Point A = 1.230" Barrel Dimensions:9 inches in front of Point A/Point B = .770" Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75" There are three takedown screws in this gun. Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 different types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & norefundable.

SPIKE CAMP RUGER 1022 CARBINE BC NUTMEG SATIN FINISH BOYDS PAD LASER PANEL ATTENTION CUSTOMERS: GRIP HAS A CONCENTRATION OF DARKER NUTMEG DYE WITH LIGHTER NUTMEG DYE CLOSER TO THE MAGWELL AREA. LAMINATES ARE NOT DYED IN HOUSE. Barrel Dimensions: Point A = 59/64" and Point B = 43/64"Center to Center of Action Screws: N/AOver All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon installed and is designed for the Factory Ruger 10/22 Semi-Auto Action, measuring 6 3/16" long.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Walnut ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Pepper ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Nutmeg ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP THUMBHOLE, SAVAGE 111 TBR, BLIND MAGAZINE, LONG ACTION, CENTER FIRE, LH ACTION, FACTORY BARREL CHANNEL Coyote Satin Finish Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside of the stock when the barreled action is removed. If the magazine box stays attached to the action you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable and nonreturnable.

SPIKE CAMP RUGER AMERICAN CENTERFIRE SA DBM FBC Blaze Satin Finish Boyds Pad Initials: DRP Font #1 Pillar Bedding Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: Not compatible with 7.62x39 caliber due to steel mag liner. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

SPIKE CAMP MOSIN NAGANT M44 MBC Sky Satin Finish Boyds Pad Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet to accept the Mosin Nagant 91/30 Barreled action. Alternate models will work but minor fitting may be needed. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with the handguard. Our stocks are designed for the straight bolt. With fitting experience, they can be inlet for any bolt. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA SAV 110 TBR 1-PC FP BBC Nutmeg High Gloss Boyds Pad Black Grip Cap Pillar Bedding LOP 12 3/4" Barrel Dimensions: Point A = 1 1/16" and Point B = 15/16" Center to Center of Action Screws: 5 1/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on the Accessories Page.ATTENTION CUSTOMERS: You will need your factory Floor Plate, Front Action Screw, Rear Action Screw, Wood Screw, Trigger Guard, Rear Action Screw spacer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.All Rapid Fire sales are final! Nonrefundable & nonreturnable.