Accessories

This extended LOP butt plate assembly will increase the LOP from the standard butt plate assembly minimum and maximum by approximately 3/8" but still provide full range of adjustability. It will provide vertical adjustability in both directions (up or down) of approximately 1-11/16" (one and eleven sixteenths inches) Removal of the butt pad is required for adjustment. Loosen the two clamping screws, adjust to desired vertical placement, tighten clamping screws and reinstall butt pad.

This butt plate assembly will increase the LOP from the standard butt plate assembly minimum and maximum by approximately 3/8" but still provide full range of adjustability. It will provide vertical adjustability in both directions (up or down) of approximately 1-11/16" (one and eleven sixteenths inches) Removal of the butt pad is required for adjustment. Loosen the two clamping screws, adjust to desired vertical placement, tighten clamping screws and reinstall butt pad.

ROTATING AT-ONE & AGILITY BUTT ASSEMBLY Attaches to the existing butt plate of the At-One and Agility adjustable butt plate assembly. It will provide rotation on the recoil pad to allow the user to position the pad to fit their shooting style. To install: Remove the butt pad from the adjustable butt plate assembly, attach using the mounting screws and reattach the butt pad. Increases LOP by approximately 3/4" when installed. Will work in conjunction with the vertically adjustable assembly. Technical Specification: 5.7 degrees per rotation index, 40 degrees per side (right and left) with 80 degrees of full index range. Engraved index identifier marks. Aluminum housing, stainless dowel pins, black phosphate steel snap ring. Black anodized coating. The threaded knob is hard anodized and Teflon impregnated to prevent gulling of the threads. Operates without tools.

Thicker, more vertical grip designed for prone shooting. Over molded components are a plastic substrate with over molded panels of rubber. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Thicker, more vertical grip designed for prone shooting. Plastic substrate – Super Tough, Impact Modified, Heat Stabilized Nylon. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Swept back pistol grip design. Over molded components are a plastic substrate with over molded panels of rubber. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

This Quick Detach Sling Swivel features a 1.25" Loop for compatibility with a wide variety of sling types and is quickly and easily installed or removed from our At-One QD Sling Socket via its large push button. The QDS swivel is constructed of Stainless Steel for strength and durability, blued finish and is a 100% US Made product.

Blue Skulls Dipped component set for Boyds At-One Stock. Includes Sleek and slender standard plastic forend - Width 1-3/4" at rear to 1-7/16" at front; Traditional swept back plastic pistol grips; Overmolded adjustable comb and plastic bottom cap. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Zombie Hunter Skulls Dipped component set for Boyds At-One Stock. Includes Sleek and slender standard plastic forend - Width 1-3/4" at rear to 1-7/16" at front; Traditional swept back plastic pistol grips; Overmolded adjustable comb and plastic bottom cap. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Zombie Hunter Dipped component set for Boyds At-One Stock. Includes Beaver-style; flat design overmolded forend - Width 2" at rear to 1-13/16" at front; Thicker, more vertical plastic grip designed for prone shooting; Overmolded adjustable comb and plastic bottom cap. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Zombie Hunter Dipped component set for Boyds At-One Stock. Includes Sleek and slender standard plastic forend - Width 1-3/4" at rear to 1-7/16" at front; Traditional swept back plastic pistol grips; Overmolded adjustable comb and plastic bottom cap.

Red Dipped component set for Boyds At-One Stock. Includes Sleek and slender standard plastic forend - Width 1-3/4" at rear to 1-7/16" at front; Traditional swept back plastic pistol grips; Overmolded adjustable comb and plastic bottom cap. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Pink Camo Dipped component set for Boyds At-One Stock. Includes Beaver-style; flat design overmolded forend - Width 2" at rear to 1-13/16" at front; Thicker, more vertical plastic grip designed for prone shooting; Overmolded adjustable comb and plastic bottom cap. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

Pink Camo Dipped component set for Boyds At-One Stock. Includes Sleek and slender standard plastic forend - Width 1-3/4" at rear to 1-7/16" at front; Traditional swept back plastic pistol grips; Overmolded adjustable comb and plastic bottom cap. ATTENTION CUSTOMERS: HAND GRIP SETS ARE NOT COMPATIBLE WITH AT-ONE THUMBHOLE STOCKS.

This kit is compatible with short action caliber Mossberg Patriot models with AICS platforms and can be used to convert a rotary detachable magazine to an AI Magazine. Not compatible with 350 Legend and 450 Bushmaster calibers due to cartridge design. This kit is not compatible with factory stocks, must have a Boyds Hardwood Gunstock in order to convert to the AI Magazine.

Machined black anodized Tikka T3 Aluminum Bottom Metal with trigger guard latch & spring with roll pin. Compatible with Tikka T3, T3x, & T3 Lite Boyds Gunstocks. You will use your factory takedown screws to install.

Machined black anodized Tikka T3 Lite Aluminum Bottom Metal with trigger guard latch & spring with roll pin. Compatible with Tikka T3 & T3 Lite Boyds Gunstocks. You will use your factory takedown screws to install.

The Rail Sling Attachment provides a forward sling attachment point for the Magpul MS3 and other clip-in sling systems. •Solid Steel construction •Milspec manganese phosphate finish •Compatible with 1913 Picatinny rails •UPC # 873750005249

Flex Fit Black: This patented Flexfit(TM) mid-profile, structured cap sports a six-panel, 3 1/2" crown, Permacurv visor with silver under-visor, and sewn eyelets. Boyds are designed with flat embroidered front, American flag embroidered on the left side, and official Boyds logo on the back. Sweat-resistant 84% nylon/14% cotton/2% spandex, and 98/2 cotton twill/spandex. Cap Measurements: S/M (6 3/4"-7 1/4"), L/XL (7 1/8"-7 5/8")

Flex Fit Red Stripe: This patented Flexfit(TM) Sport-Tek Flex-Fit Colorblock Performance Cap wicks sweat like a champ! 84% nylon/14% cotton/2% spandex. Boyds are designed with flat embroidered front, American flag embroidered on the left side, and official Boyds logo on the back. Cap Measurements: S/M (6 3/4"-7 1/4"), L/XL (7 1/8"-7 5/8")