Gunstocks

PRO VARMINT CZ® 452-2E AMERICAN, SHORT ACTION, CLIP FEED, LH ACTION, FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 27.0"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee."

PRO VARMINT CZ® 452 2E AMERICAN BOLT, SHORT ACTION, CLIP, FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 27"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee."

PRO VARMINT CZ® 527 AMERICAN, SHORT ACTION, CLIP FEED, LH ACTION, BULL BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 0.99" and Point B = 0.885"Center to Center of Action Screws: 5.5" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION: THIS STOCK IS NOT COMPATIBLE WITH THE CZ 527 M CARBINE MODEL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

BRITISH LEE ENFIELD® #5 MKI FOREND ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/4 " Barrel Channel Point B: 13/16 " Receiver Edge to Center of Mounting Screw: 6 3/32" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 16 3/8 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. ATTENTION CUSTOMERS: These parts are inlet for military barrel contour. These are not full length military style forends and do not come with upper handguards.

BROWNING T-BOLT (POST 2006), SPIKE CAMP, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 0.82" and Point B = 0.72"Center to Center of Action Screws: 2.47" Over All Length of Part: 30.375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Key element is rotory magazine and tang safety, inlet is based on .17HMR. Length of mag opening: 1.973"ATTENTION CUSTOMERS: You will need the 2-take down screws and plastic mag insert from your original stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

BROWNING® AB-2 SSA , SPIKE CAMP, 2PC HINGED FP, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1.176" and Point B = .842"Center to Center of Action Screws: 6.66"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, take down screws, trigger guard and screw from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee .

SPIKE CAMP, TIKKA T3, DETACHABLE BOX MAGAZINE, LEFT HAND ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 9/64" and Point B = 55/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee .

HERITAGE, SAUER 100 LONG ACTION LEFT HAND STOCK RIGHT HAND ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PLATINUM, SAUER 100 LONG ACTION LEFT HAND STOCK RIGHT HAND ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

HERITAGE, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PLATINUM, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PRAIRIE HUNTER, SAUER 100 LONG ACTION LEFT HAND STOCK RIGHT HAND ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PRO VARMINT, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

VARMINT THUMBHOLE, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PRAIRIE HUNTER, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

FEATHERWEIGHT THUMBHOLE, SAUER 100 LONG ACTION LEFT HAND STOCK RIGHT HAND ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

FEATHERWEIGHT THUMBHOLE, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CLASSIC, SAUER 100 LONG ACTION LEFT HAND STOCK RIGHT HAND ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CLASSIC, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

SPIKE CAMP THUMBHOLE, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

AT-ONE THUMBHOLE, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

AT-ONE, SAUER 100 LONG ACTION FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/2" and Point B = 3/4 " Center to Center Action Screws: 7 5/8"ATTENTION CUSTOMERS : Washer Stock-Rear Action NOT required for Boyds stock. You will need your factory Floor Plate, Rear Action Screw, Front Action Screw, Front Action Screw "Nut". We will provide the Recoil Lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

SPIKE CAMP, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

AT-ONE THUMBHOLE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

AT-ONE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

HERITAGE, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PLATINUM, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

HERITAGE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PLATINUM, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PRAIRIE HUNTER, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

VARMINT THUMBHOLE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PRAIRIE HUNTER, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

FEATHERWEIGHT THUMBHOLE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CLASSIC, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CLASSIC, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.