Rapid Fire Products

ATONE THUMBHOLE RUGER AMERICAN CENTERFIRE LA DBM ROYAL PILLARS ENGRAVED INITIALS "JHL" Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 37/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with AI or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

ATONE THUMBHOLE RUGER AMERICAN CENTERFIRE LA DBM APPLEJACK Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 37/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with AI or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

ATONE BROWNING XBOLT SA FBC PEPPER Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 4 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

ATONE THUMBHOLE BROWNING XBOLT LA FBC COYOTE Barrel Dimensions: Point A = 1 7/64" and Point B = 45/64" Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. The Safety is located on the tang and the Bolt Release is on the side of the receiver. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

ATONE HOWA 1500 SA BBC COYOTE ENGRAVED SYMBOL Barrel Dimensions: Point A = 1 1/4" and Point B = 1" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the HOWA 1500 Short Action, with factory Varmint Contour. Numerous other models have been manufactured using this action design. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

PRO VARMINT RUGER 77 MKII SA FBC GREEN TEXTURED PAINT 1" LIMBSAVER ATTENTION CUSTOMERS: PAINT RUBBED OFF ON RIGHT SIDE BUTTSTOCK/CHEEK AREA Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up.ATTENTION CUSTOMERS: Some WSM calibers may require modifications to the magwell due to the width in the magazine sleeve in the firearm. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

ATONE TC COMPASS DBM LA FBC SHADY CAMO PILLARS Barrel Dimensions: Point A = 1.11" and Point B = 0.68"Center to Center of Action Screws: 7.60"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the front takedown screw from your factory stock. Boyds will provide the recoil lug, rear magazine ledge, front magazine latching tab, front washer, trigger guard, trigger guard screw and rear takedown screw. Long Action Calibers, 270 Win, 300 Win mag,, 30-06 Spfld, 7mm Rem Mag. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

VARMINT THUMBHOLE SAVAGE A17 SEMI AUTO DBM FBC FOREST CAMO 14 1/4" LOP 1" LIMB SAVER LASER PANEL Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: We provide the T-nut sert and mag tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

ATONE SAVAGE AXIS DBM LA FBC COYOTE Barrel Dimensions: Point A = 1 11/32"; and Point B = 23/32" ATTENTION CUSTOMERS: For long action calibers; 25-06 REM, 30-06 SPFLD, or 270 WIN. When assembling, hold the barrel in the center of the channel and tighten screws. Length of Mag Box: 3 49/64" Center to Center of Action Screws: 4 25/32"; Over All Length of Part: 31 1/2" Comes with Boyds 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ;***Stainless Steel Metal trigger guards are also available: PN 100662. Blued Metal trigger guards are also available: PN 100661. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds #39; House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

CLASSIC REMINGTON 700 BDL SA BBC CIRCASSIAN XX WALNUT 13 1/2" LOP BLACK POLYMER TIP ATTENTION CUSTOMERS: TIP HAS WALNUT STAIN MARKS ON IT Barrel Dimensions: Point A = 1 9/32" and Point B = 31/32" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlet for the factory varmint contour barrel channel. This stock is designed for the Remington 700 Right Hand Short Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

ATONE SAVAGE 111 TBR DBM LA FBC BLAZE FRONT PILLAR ONLY ENGRAVED SYMBOL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. br> All Rapid Fire sales are final! Nonrefundable & nonreturnable.

RIMFIRE THUMBHOLE RUGER 10/22 .920 PEPPER 14" LOP 1" LIMBSAVER Barrel Dimensions: Point A = .920" and Point B = N/A Center to Center of Action Screws: N/A Over All Length of Part: 26 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Comes with brass mounting escutcheon. This stock is designed for the factory Ruger 10/22 semi auto action measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

VARMINT THUMBHOLE TIKKA T3 LITE BBC NUTMEG 1" LIMBSAVER Barrel Dimensions: Point A = 1 9/64" and Point B = 55/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. ***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09210*** It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. br> All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERITAGE MAUSER LR #1 BC BLACK TEXTURED PAINT BOYDS PAD Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

PRAIRIE HUNTER REMINGTON 788 SHORT RECEIVER FBC WALNUT HIGH GLOSS WALNUT GRIP CAP ANGLED WALNUT TIP LASER PANEL Barrel Dimensions: Point A = 1 13/64" and Point B = 13/16" Center to Center of Action Screws: 6 3/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Remington 788 Short Action.Short Action Calibers- 222 Rem, 223 Rem,22-250 Rem,30-30 Win. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLATINUM WINCHESTER 70 NFP LA FBC POST 64 NUTMEG BLACK GRIP CAP ANGLED BLACK TIP BOYDS PAD Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel. All Rapid Fire sales are final! Non-refundable & non-returnable.

PRO VARMINT WEATHERBY VG LA FBC FOREST CAMO BOYDS PAD Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 3/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Long Action. Numerous other models have been manufactured using this action design. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Non-refundable & non-returnable.

PRAIRIE HUNTER MOSSBERG PATRIOT SA DBM FBC ROYAL BOYDS PAD INITIALS "718" ATTENTION CUSTOMERS: TINY DENT ON BOTTOM BY FRONT SWIVEL STUD Barrel Dimensions: Point A = 1.175" and Point B = .735"Center to Center of Action Screws: 4.715"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the mag insert, mag box and take down screws from your factory stock. We will provide a metal trigger guard, rear action screw and wood screw.ATTENTION CUSTOMERS: Mossberg Patriot SA AI Mag Assembly kits are available on the Accessories page, Part# A09164. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FEATHERWEIGHT THUMBHOLE SAVAGE AXIS LA FBC SKY 1" LIMBSAVER Barrel Dimensions: Point A = 1 11/32" and Point B = 23/32"ATTENTION CUSTOMERS: For long action calibers; 25-06 REM, 30-06 SPFLD, or 270 WIN. When assembling, hold the barrel in the center of the channel and tighten screws.Length of Mag Box: 3 49/64" approximately Center to Center of Action Screws: 4 25/32"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. Blued Metal trigger guards are also available: PN 100661. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.br All Rapid Fire sales are final! Non-refundable & non-returnable.

ATONE SAVAGE AXIS LA FBC NUTMEG Barrel Dimensions: Point A = 1 11/32"; and Point B = 23/32" ATTENTION CUSTOMERS: For long action calibers; 25-06 REM, 30-06 SPFLD, or 270 WIN. When assembling, hold the barrel in the center of the channel and tighten screws. Length of Mag Box: 3 49/64" Center to Center of Action Screws: 4 25/32"; Over All Length of Part: 31 1/2" Comes with Boyds 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ;***Stainless Steel Metal trigger guards are also available: PN 100662. Blued Metal trigger guards are also available: PN 100661. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds #39; House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLASSIC SAVAGE 110 TBR BLIND MAG LA STGF FBC FOREST CAMO BOYDS PAD FRONT PILLAR Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

SPIKE CAMP RUGER AMERICAN CENTER FIRE LA DBM FBC WALNUT HIGH GLOSS Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 37/64" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with AI or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLASSIC STEVENS 200 TBR BLIND MAG SA STGF FBC WALNUT BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLASSIC CZ550 AMERICAN LA FBC NUTMEG BLACK GRIP CAP 1" LIMBSAVER ANGLED BLACK TIP FRONT PILLAR ONLY It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64"Center to Center of Action Screws: 7 53/64"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP HOWA 1500 SA FBC WALNUT Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the HOWA 1500 Short Action, with factory tapered barrel channel. Numerous other models have been manufactured using this action design. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FEATHERWEIGHT THUMBHOLE REMINGTON 700 LA SENDARO 1 PC HINGED FP BBC FOREST CAMO Barrel Dimensions: Point A = 1.230" and Point B = .905"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.50"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and mag well from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect./p> All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP STEVENS 200 TBR BLIND MAG SA CNTF FBC PEPPER PILLAR FRONT ONLY Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

ATONE SAVAGE 12 TBR DBM BBC NUTMEG FRONT PILLAR ONLY Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE SAVAGE TBR 114 LONG ACTION DBM FBC FOREST CAMO 1" LIMB SAVER Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! "

HERITAGE WINCHESTER 70 SUPER SHORT ACTION BLIND MAG POST 64 PEPPER BOYDS PAD PILLARS Barrel Dimensions: where barrel meets receiver/Point A=1.138" Barrel Dimensions: 9 inches in front of Point A/Point B= .668" Center to Center of Action Screws: 6.35" Attention Customers: Winchester Super Short Magnum-Blind Mag-NO FLOOR PLATE Attention Customers: It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PRO VARMINT SAVAGE A22 SEMI AUTO DBM FBC SKY BOYDS PAD LASER PANEL Barrel Dimensions: Point A = 63/64" and Point B = 47/64" Center to Center of Action Screws: 7.46" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :You will need the washer from the factory rear take down screw for the new rear take down screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable. "

SPIKE CAMP SAVAGE 93 LEFT HAND ACTION BULL BARREL COYOTE Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

CLASSIC SAVAGE 110 BBR DEBM LA FBC WALNUT BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09212. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERITAGE, SAVAGE 116 TBR, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, FACTORY BARREL CHANNEL COYOTE, BLACK GRIP CAP, KICK EEZ PAD, FRONT ACTION SCREW PILLAR BEDDING Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All Rapid Fire sales are final! Non-refundable & non-returnable.

FEATHERWEIGHT THUMBHOLE WINCHESTER 70 SA 2PC FP FBC SKY KICKEEZ PAD Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. THIS STOCK WILL NOT WORK FOR THE WSSM CALIBER RIFLES. PRE 1984 ACTIONS ARE BASED ON THE LONG ACTION RECEIVER. THESE STOCKS ARE DESIGNED FOR THE WINCHESTER® MODEL 70 SHORT ACTION 2-PIECE HINGED FLOOR PLATE MODEL, WITH STANDARD FACTORY TAPERED BARREL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FEATHERWEIGHT THUMBHOLE SAVAGE 110 TBR DBM LA FBC ZOMBIE HUNTER FRONT PILLAR Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

PRAIRIE HUNTER MAUSER LARGE RING #1 BC COMMERCIAL FP LH STK RH ACT FOREST CAMO 1" LIMBSAVER 13" LOP Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8.475" Over All Length of Part: 31 1/2" Comes with Boyds 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is for Mauser Large Ring Guns that utilize the shorter commercial floor plate, see dimensions to determine application. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLASSIC SAVAGE 10 TBR DBM SA BULL BARREL WALNUT 13 1/4" LOP BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

PRO VARMINT BERGARA B14R SA DBM SKY PILLARS BOYDS PAD SATIN FINISH PRO VARMINT BERGARA B-14R (RIMFIRE) SHORT ACTION DBM BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 15/16" Center to Center Action Screws: 6 1/2" ATTENTION CUSTOMERS: You will need your factory Floor Plate, Front and Rear Action Screws. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

CLASSIC SAVAGE 10 BBR DBM FBC WALNUT WHTIE LINE SPACER BLACK GRIP CAP BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect All Rapid Fire sales are final! Nonrefundable & Nonreturnable.