Gunstocks

MAUSER 1910, COSTA RICA , AT-ONE THUMBHOLE, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77 MKII HAWKEYE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the LEFT hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 700 ADL, SHORT ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlett for standard factory tapered barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN X7S, LONG ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Stock is designed for the X7 Long Action receiver. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 10 TBR, BLIND MAGAZINE, SHORT ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

MAUSER MARK X, CHARLES DALY, AT-ONE THUMBHOLE, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77 MKII HAWKEYE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON® 597 HBC Barrel Dimensions: Point A = 7/8" and Point B = 7/8" Center to Center of Action Screws: 5 7/16" Over All Length of Part: 30 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:If converting from plastic stocked 597 you will need 1 front and 1 rear stock insert used on the 597 LSS. These inserts can be purchased on the Accessories page, part number A09163 & A09162. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN X7S, SHORT ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Stock designed for the Marlin X7 Short Action with factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 10 TBR, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 1 1/16" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. v This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

MAUSER CENTURION FN, AT-ONE THUMBHOLE, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77 MKII HAWKEYE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 514 .22, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = .780" and Point B = .720" Over All Length of Part: 32" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need one takedown screw from your stock. The barrel will not be free floated on this model. We will provide the trigger guard with screws. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN X7C, LONG ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Stock is designed for the X7 Long Action receiver. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 10 TBR, BLIND MAGAZINE, SHORT ACTION, STAGGERED FEED, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BROWNING T-BOLT (POST 2006), AT-ONE THUMBHOLE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 0.82" and Point B = 0.72"Center to Center of Action Screws: 2.47" Over All Length of Part: 30.375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Key element is rotory magazine and tang safety, inlet is based on .17HMR. Length of mag opening: 1.973"ATTENTION CUSTOMERS: You will need the 2-take down screws and plastic mag insert from your original stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77/22®, FACTORY BARREL CHANNEL, LAMINATED STOCK Barrel Dimensions: Point A = 15/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 30" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 Bolt Action 22 Long Rifle. Early plastic stocks will require additional mounting hardware to use our stocks. Please contact Ruger or Brownells (800) 741-0015 for the metal trigger guard and clip assembly. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 510, SHORT ACTION , FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 49/64" and Point B = 23/32" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need one takedown screw from your stock. The barrel will not be free floated on this model. This stock dones not require the escutcheon from the original stock. We will provide the trigger guard with screws. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN X7C, SHORT ACTION, FACTORY BARREL CHANNEL, ZZ F Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Stock designed for the Marlin X7 Short Action with factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 10 TBR, BLIND MAGAZINE, SHORT ACTION, CENTERFEED, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77 MKII, LONG ACTION, LEFT HAND ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the LEFT hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 78 ADL, SHORT ACTION, BULL BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 9/32" and Point B = 31/32" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlett for a factory varmint contour barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE MARLIN XL7, LONG ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4"Center to Center of Action Screws: 7 1/2"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Stock is designed for the X7 Long Action receiver.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

AT-ONE THUMBHOLE, SAVAGE® 93E MKII, LEFT HAND ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 11/16" and Point B = 11/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77 MKII, SHORT ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up.ATTENTION CUSTOMERS: Some WSM calibers may require modifications to the magwell due to the width in the magazine sleeve in the firearm. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 78 ADL, LONG ACTION ,FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Long Action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN® 925, CLIP FEED, BULL BARREL CHANNEL, STOCK, ZZ Barrel Dimensions: Point A = 13/16" and Point B = 13/16"Center to Center of Action Screws: 4 7/8"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: These stocks are designed for inlett trigger guard and floor plate. Variations exist on the safety for this model, minor fitting of safety may be needed. ATTENTION CUSTOMERS:If converting from composite stock to a Boyds hardwood gunstock you will need to purchase the Marlin Rimfire Trigger Guard on the Accessories page, part number A09166.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE® 93 BOLT ACTION, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER 77 MKII, LONG ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 78 ADL, SHORT ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlett for standard factory tapered barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE MARLIN® XT, CLIP FEED, BULL BARREL CHANNEL, STOCK, ZZ Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 4 7/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for inlett trigger guard and floor plate. Variations exist on the safety for this model, minor fitting of safety may be needed. ATTENTION CUSTOMERS: If converting from composite stock to a Boyds hardwood gunstock you will need to purchase the Marlin Rimfire Trigger Guard on the Accessories page, part number A09166. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE® 93E MKII, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 11/16" and Point B = 11/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31.5" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need the 2 Take Down Screws and Clip from your factory stock. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER® 10/22®, CBC STOCK Barrel Dimensions: Point A = 59/64" and Point B = 43/64"Center to Center of Action Screws: N/AOver All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon installed and is designed for the Factory Ruger 10/22 Semi-Auto Action, measuring 6 3/16" long.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 7, SHORT ACTION, MAG BARREL CONTOUR, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 13/16" Center to Center of Action Screws: 5 15/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Designed for the hinged floor plate Remington Model 7 with Magnum barrel contour. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Stock is designed for the X7 Long Action receiver. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE® 93E MKII, BULL BARREL CHANNEL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER® 10/22®, .920 BARREL CONTOUR STOCK Barrel Dimensions: Point A = .920" and Point B = .920" Center to Center of Action Screws: N/A Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon and is designed for the Factory Ruger 10/22 Semi-Auto Action, measuring 6 3/16" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON 7, SHORT ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 11/64" and Point B = 37/64" Center to Center of Action Screws: 5 15/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Designed for the hinged floor plate Remington Model 7 with factory/Sporter barrel contour. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN X7, SHORT ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Stock designed for the Marlin X7 Short Action with factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BROWNING T-BOLT, AT-ONE THUMBHOLE, SHORT ACTION, CLIP FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 23/32" Center to Center of Action Screws: 5 47/64" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: This inletting will fit all T-Bolt models manufactured from 1965-1974. The design of this gun will not allow a free floated barrel. Boyds' inlets will have a barrel pad at the front of the barrel channel. You will need the takedown screw, trigger, and floor plate with screw clip. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE® 93R, LEFT HAND ACTION, BULL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the receiver) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc : PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON® 710, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions:where barrel meets reciever/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 diffrent types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.:All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, PERUVIAN MAUSER 1935, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 13/16" and Point B = 13/16"Center to Center of Action Screws: 4 7/8"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: These stocks are designed for inlett trigger guard and floor plate. Variations exist on the safety for this model, minor fitting of safety may be needed. ATTENTION CUSTOMERS:If converting from composite stock to a Boyds hardwood gunstock you will need to purchase the Marlin Rimfire Trigger Guard on the Accessories page, part number A09166.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE® 93R, BULL BARREL CHANNEL STOCK , FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the receiver) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON® 541-T BOLT, CLIP FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 0.821" and Point B = .821"Center to Center of Action Screws: 3.48" Over All Length of Part: 27.00"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and trigger guard from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, PERUVIAN MAUSER 1909, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN® 795, CLIP FEED, FACTORY BARREL CHANNEL, STOCK, ZZ, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: N/A Width of Trigger Guard: 27/32" Length of Trigger Guard: 6 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to fit the Marlin Model 795 Clip Feed Rifle with the U-shaped trigger guard. Early models are longer and are shaped differently. DIP Products sells new U-shaped trigger guards if desired. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE® MKII, LEFT HAND ACTION, BULL BARREL CHANNEL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE REMINGTON® 700 MOUNTAIN LA DBM FBC Barrel Dimensions: Point A = 1.195" and Point B = 0.606"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad. Barrel contour for the light weight "Mountain" version.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.