Gunstocks

PLATINUM, YUGOSLAVIAN MAUSER 48, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS :These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

WINCHESTER® 93, 12 GA, STANDARD GROOVED FOREND, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Magazine Tube Width: 1 1/4" Magazine Tube Shoulder to Shoulder: 6 5/8" Over All Length of Part: 6 3/4" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.143" and Point B = 0.766"Center to Center of Action Screws: 7.465" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This inlet is for the Model 70 Pre WWII model. There are differences between the model 70 pre WWII and the Model 70 Pre 64. Most notable is that the Pre WWII has a clover leaf rear tang on the receiver. You must identify which model you have prior to ordering. You will need take down screws and 2 piece floor plate from the factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks.

WINCHESTER® 93, 12 GA STOCK, ZZ All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DBL .410 GA SPLINTER FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A " Barrel Channel Point B: N/A " Receiver Edge to Center of Mounting Screw: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A " Over All Length of Part: 7 1/2" Over All width at receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These forends are designed to accept Internal spring clip hardware. Do to variations for this model final fitting of hardware and the drilling for mounting screws may be required.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DBL TYPE 1 16GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: N/A Top Tang length: N/A Bottom Tang width: N/A Bottom Tang length: N/A Stock height at receiver: 2 1/8" Stock width at receiver: 1 7/16" Overall Length of Stock: 13 1/4" Measurement of Receiver Mounting Bolt: 5 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These stocks are designed for the V notch receiver.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 13/16" Top Tang Length: 3 3/4" Bottom Tang Width: 1/2" Bottom Tang Length: 3 3/4" Stock Height at Receiver: 1 1/4" Stock Width at Receiver: 1 1/4" Overall Length of Stock:12 7/8" Measurement of Receiver Mounting Bolt: N/A" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These are field design stocks with Boyds plastic butt plates. These are not designed to accept crescent shaped butt plates.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester? Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: N/A Top Tang length: N/A Bottom Tang width: N/A Bottom Tang length: N/A Stock height at receiver: 2 1/8" Stock width at receiver: 1 7/16" Overall Length of Stock: 13 1/4" Measurement of Receiver Mounting Bolt: 5 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These stocks are designed for the V notch receiver.

WORTHINGTON DBL TYPE 1 20GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, WINCHESTER 70, SHORT ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester? Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: N/A Top Tang length: N/A Bottom Tang width: N/A Bottom Tang length: N/A Stock height at receiver: 2 1/8" Stock width at receiver: 1 7/16" Overall Length of Stock: 13 1/4" Measurement of Receiver Mounting Bolt: 5 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These stocks are designed for the V notch receiver.

WINCHESTER® XTR 16GA STOCK, ZZ All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. THIS STOCK WILL NOT WORK FOR THE WSSM CALIBER RIFLES. PRE 1984 ACTIONS ARE BASED ON THE LONG ACTION RECEIVER. THESE STOCKS ARE DESIGNED FOR THE WINCHESTER® MODEL 70 SHORT ACTION 2-PIECE HINGED FLOOR PLATE MODEL, WITH STANDARD FACTORY TAPERED BARREL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DBL TYPE 1, 12GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel at Receiver: Approximately 1" Barrel Channel at End: 11/16" Receiver Edge to Center of Mounting Screw: 6 7/8" Shoulder to Shoulder: 6 11/16" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Stock Height at Receiver: 2" Stock Width at Receiver: 1 13/32" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: 7 7/32" BUTTPLATE It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 13/16" Top Tang Length: 3 3/4" Bottom Tang Width: 1/2" Bottom Tang Length: 3 3/4" Stock Height at Receiver: 1 1/4" Stock Width at Receiver: 1 1/4" Overall Length of Stock:12 7/8" Measurement of Receiver Mounting Bolt: N/A" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These are field design stocks with Boyds plastic butt plates. These are not designed to accept crescent shaped butt plates.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. THIS STOCK WILL NOT WORK FOR THE WSSM CALIBER RIFLES. PRE 1984 ACTIONS ARE BASED ON THE LONG ACTION RECEIVER. THESE STOCKS ARE DESIGNED FOR THE WINCHESTER® MODEL 70 SHORT ACTION 2-PIECE HINGED FLOOR PLATE MODEL, WITH STANDARD FACTORY TAPERED BARREL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel at Receiver: Approximately 1" Barrel Channel at End: 11/16" Receiver Edge to Center of Mounting Screw: 6 7/8" Shoulder to Shoulder: 6 11/16" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DOUBLE, TYPE 2, 12GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/4" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1.127" Barrel Channel Point B: 1.037" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: 2.26" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 8.49" Over All Width at Receiver: 1 3/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.. ATTENTION CUSTOMERS:Please note: This is the exposed plate 37 forend.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 1" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9 3/4" Over All Width at Receiver: 1 3/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Please note: This is the exposed plate 37 forend.

WESTERN FIELD SB300 C TYPE 1 .410GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Boyds' Sterling Thumbhole Buttstock for the WESTERN FIELD 502-26FR 12ga. shotgun.Stock comes with mounting bolt. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A Top Tang Length: N/A Bottom Tang Width: 1/2" Bottom Tang Length: 3/8" Stock Height at Receiver: 1 13/16" Stock Width at Receiver: 1 7/16" Overall Length of Stock: 12 3/4" Comes with 3/4" vented pad All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WESTERN FIELD SB300 C TYPE 1 16GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WESTERN FIELD 10-SD247A STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang width: 9/16" Top Tang length: 2 7/8" BottomTang width: 9/16" BottomTang length: 2 13/16" Stock height at receiver: 1 15/16" Stock width at receiver: 1 3/8" Overall Length of Stock: 15" Measurement of Receiver Mounting Bolt: 4 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:The Stevens/Savage Model 94 and 24 use the same receivers. The Model 24 stock has a monte carlo style comb, the Model 94 has a straight field style comb.

WESTERN FIELD SB300C 16 GA SEMI BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 3/4" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

PRO VARMINT WESTERN FIELD MAUSER® EJN-757, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Length of Floor Plate 8 11/16" Over All Length of Part: 31 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour Barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SWESTERN FIELD SB300C 16 GA BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 7/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WESTERN FIELD 60SB 12 GA RIBBED FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WESTERN FIELD 740 PISTOL GRIP STOCK Length of Pull 13 3/4"Top Tang width 1/2"Top Tang length 3 1/16"BottomTang width 9/16"BottomTang length 3 1/8 "Stock height at receiver 1 3/4 "Stock width at receiver 1 1/2 "

WESTERN FIELD SB300 C TYPE 1 20GA STOCK, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE WESTERN FIELD MAUSER 720-A #1 BC Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Length of Floor Plate 8 11/16" Over All Length of Part: 31 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour Barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, WESTERN FIELD MAUSER 720, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WESTERN FIELD SB300C 20 GA SEMI BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 3/4" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

STERLING WESTERN FIELD 600 ERI 12 GA STOCK Stock comes with mounting bolt. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A Top Tang Length: N/A Bottom Tang Width: 1/2" Bottom Tang Length: 9/16" Stock Height at Receiver: 1 15/16" Stock Width at Receiver: 1 7/16" Overall Length of Stock: 14" Comes with 3/4" vented recoil pad All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These stocks are designed for the larger frame models.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, WESTERN FIELD MAUSER 720, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.