Gunstocks

HERITAGE, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, BROWNING A-BOLT 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, BROWNING A-BOLT 2, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions:Where Barrel meets the receiver/ Point A = 1.175" Barrel Dimensions: 9 inches in front of Point A/ Point B = .680 Center to Center of Action Screws: 7.2" Over All Length of Part: 31/1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and trigger guard.Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. Attention Customer WSM calibers may require widening of the magazine box opening. Width of mag box opening Front: 15/16" Rear: 1 1/8".All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29.75" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have been used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.