Gunstocks

PRAIRIE HUNTER RUGER AMERICAN RANCH GEN 2, SHORT ACTION, AR MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE RUGER AMERICAN RANCH GEN 2, SHORT ACTION, AR MAGAZINE, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE RUGER AMERICAN RANCH GEN 2, SHORT ACTION, AR MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC RUGER AMERICAN RANCH GEN 2, SHORT ACTION, AR MAGAZINE, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC RUGER AMERICAN RANCH GEN 2, SHORT ACTION, AR MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

SPIKE CAMP THUMBHOLE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

AT-ONE THUMBHOLE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

AT-ONE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

LEFT HAND HERITAGE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

Traditions Vortek Pistol Grip Stock Overall length 13 8/16" Top Tang width 14/16" Top Tang Length 1 4/16" Stock Height at Receiver 1 6/16" Stock Width at Receiver 1 6/16"ATTENTION CUSTOMERS: You will need your factory receiver mounting bolt, measuring 4 5/16". ATTENTION CUSTOMERS: This inlet is for the older model firearm with a removable trigger guard; newer models have the trigger guard molded into the stock and are incompatible. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Traditions Vortek MUZZLELOADER FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Rear 1" Barrel Channel Front 15/16" Receiver Edge to Center of Mounting Screw 3 4/16" Over All Length of Part: 10 12/16" ATTENTION CUSTOMERS: You will need your ramrod retention clip and screw as well as the forend takdown screw from the factory original. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Top Tang Width: 0.968"Top Tang Length: 3.822"Bottom Tang Width: 0.668"Bottom Tang Length: 3.822"Stock Height at Receiver: 1.315"Stock Width at Receiver: 1.165"Overall Length of Stock:13.75"Measurement of Receiver Mounting Bolt: N/ABUTTPLATEIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the take down screw from your factory stock.ATTENTION CUSTOMERS: THIS IS DESIGNED FOR THE 17 HMR CALIBER. NOT COMPATIBLE WITH ANY OTHER CALIBER.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

STRAIGHT GRIP WINCHESTER® 94 WRANGLER STK ZZIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.