Gunstocks

SPIKE CAMP, MARLIN® 25 Barrel Dimensions: Point A = 0.745" and Point B = 0.745"Center to Center of Action Screws: n/aOver All Length of Part: 29 3/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the Floorplate & Screw and take down screw from your factory stock.  We will provide trigger guard & screws. Barrel does not float.ATTENTION CUSTOMERS: Will not work with the 25MN, 25M, or 25N model variation. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.  Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, RUGER® 77, TANG SAFETY, LONG ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4"Center to Center of Action Screws: 7 3/4"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:These stocks are designed for the original Ruger model 77 with rear tang safety. Newer models will have safety located by the bolt handle on right hand side of action.

SPIKE CAMP THUMBHOLE, SAVAGE 10 TBR, BLIND MAGAZINE, SHORT ACTION, CENTERFEED, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BRNO ZKK-600, SPIKE CAMP, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/64" and Point B = 3/4" Center to Center of Action Screws: 7 53/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your takedown screws, mag liner, follower, and floorplate for your original stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, PERUVIAN MAUSER 1909, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, JC HIGGINS MAUSER 51, #1 BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, REMINGTON® 710, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions:where barrel meets reciever/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 29.75"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 diffrent types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.:All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE® 93E MKII, LEFT HAND ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BRNO 2E .22LR, SPIKE CAMP THUMBHOLE, BULL BARREL CHANNEL *Minor fitting in the barrel channel will be needed!*Barrel Dimensions: Point A = 1 1/16" and Point B = 15/16" Center to Center of Action Screws: 6 1/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed using metal trigger guard and floor plate and are made using barrel mounting screw model. If your action has rear receiver mounting screw please review Mag parts (if available). All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, PERSIAN MAUSER 98, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP, JC HIGGINS MODEL 50, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/8" and Point B = 23/32"Center to Center of Action Screws: 7 53/64" Over All Length of Part: 29 3/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE® 93 BOLT ACTION, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, REMINGTON® 541-T BOLT, CLIP FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 0.821" and Point B = .821"Center to Center of Action Screws: 3.48" Over All Length of Part: 27.00"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and trigger guard from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP, MAUSER VZ-24, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, PARKER HALE MAUSER 1200, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP, INTERARMS 1500, SHORT ACTION, BULL BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 1" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Short Action, with factory Varmint Contour. Numerous other models have been manufactured using this action design.

SPIKE CAMP THUMBHOLE REMINGTON® 700 MOUNTAIN LA DBM FBC Barrel Dimensions: Point A = 1.195" and Point B = 0.606"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad. Barrel contour for the light weight "Mountain" version.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP, BRNO MAUSER LR, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP, NORINCO JW-15, CLIP FEED, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 59/64" and Point B = 43/64" Center to Center of Action Screws: 3 25/32" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need the flat washer, lock washer for mounting bolt, and the receiver face plate from your stock. **Due to the possible variation in wood screw size in these original parts, the hole for the rear trigger wood screw will need to be drilled by you to accommodate the original wood screw in the original stock assembly. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP INTERARMS 1500 SHORT ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Short Action, with factory tapered barrel channel. Numerous other models have been manufactured using this action design.