Gunstocks

FEATHERWEIGHT THUMBHOLE RUGER ACF PREDATOR, SHORT ACTION, AR MAG, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER ACF PREDATOR, SHORT ACTION, AR MAG, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER ACF PREDATOR, SHORT ACTION, AR MAG, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER ACF PREDATOR, SHORT ACTION, AR MAG, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER AMERICAN CENTERFIRE, SHORT ACTION, AR MAG, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN CENTERFIRE, SHORT ACTION, AR MAG, LH STK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN CENTERFIRE, SHORT ACTION, AR MAG, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN CENTERFIRE, SHORT ACTION, AR MAG, LH STK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN CENTERFIRE, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

MARLIN® 336, EXTENDED CAP STYLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Channel Point A: 15/16"Barrel Channel Point B: 12/16"Magazine Tube Width: 11/16"Magazine Tube Shoulder to Shoulder: 9 5/8"Over All Length of Part: 9 3/4"Exposed material when installed: 9 5/8"All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:There are a few variations of Cap style forends that were made for this model. Please confirm dimensions prior to ordering.ATTENTION CUSTOMERS: This is the same as the existing 336 only with an additional .325 in length to match the currently produced rifle.

Barrel Dimensions: Point A = 11/32" and Point B = 55/64" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 11/32" and Point B = 55/64" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 20 GAUGE shotgun shell. You will need the trigger guard, floor plate/mag plate, and all take down screws from the original stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.