Gunstocks

CLASSIC, SAVAGE 10 TBR, BLIND MAGAZINE, CENTER FEED, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release (located on the side of the receiver). Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LH HERITAGE, RUGER AMERICAN RANCH CENTERFIRE LH ACT LEFT HAND STOCK FBC Barrel Dimensions: Point A = 1 3/16" and Point B = 12/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. You will need the magazine, as we will not be providing this.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with A1 or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LH PLATINUM, RUGER AMERICAN RANCH CENTERFIRE LH ACT LEFT HAND STOCK FBC Barrel Dimensions: Point A = 1 3/16" and Point B = 12/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. You will need the magazine, as we will not be providing this.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with A1 or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LH PRAIRIE HUNTER, RUGER AMERICAN RANCH LH ACT LEFT HAND STOCK FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1 3/16" and Point B = 12/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. You will need the magazine, as we will not be providing this.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with A1 or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 37/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, triggerguard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION CUSTOMERS : Does not work with A1 or AR Mags.. Long Action Calibers: 270 Win, 30-06 Spfld. "All finished parts have been CNC inlet to Boyds' House Action which is based on the rotary magazine. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

LH FT, RUGER AMERICAN RANCH LH ACT LEFT HAND STOCK FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1 3/16" and Point B = 12/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. You will need the magazine, as we will not be providing this.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with A1 or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND CLASSIC, RUGER AMERICAN RANCH, LONG ACTION, LEFT HAND STOCK, LEFT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 12/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. You will need the magazine, as we will not be providing this.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with A1 or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

lhHERT BRNO ZKK-601 FACTORY BARREL CHANNEL ZZ Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WINCHESTER® 70, SHORT ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 7/8” and Point B = 3/4"Over All Length of Part: 30 3/8"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WINCHESTER 70 COYOTE, LONG ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :These stocks are designed for the Long Action 2 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 3/4" and Point B = 45/64"Over All Length of Part: 31"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 12 BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Springfield Model A03, Remington and Smith Corona also made these rifles. The easiest way to tell between the 1903 and 1903 A3 Rifles is to note where the rear sight is located. The 1903 A3 Rifle has a rear sight mounted on the back of the action by the bolt handle and 1903 Rifle has a rear sight mounted in front of the action. The area on the LEFT hand side of the stock is relief for the magazine cut-off on the original rifles. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with handguard. These stocks do not come with a bolt cut. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS :These stocks are designed for the Long Action 1 piece floor plate design with standard factory tapered barrel. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

AT-ONE THUMBHOLE, SAVAGE 12, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: The easiest way to tell between the 1903 and 1903 A3 Rifles is to note where the rear sight is located. The 1903 A3 Rifle has a rear sight mounted on the back of the action by the bolt handle and 1903 Rifle has a rear sight mounted in front of the action. The area on the LEFT hand side of the stock is relief for the magazine cut-off on the original rifles. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with handguard. These stocks do not come with a bolt cut. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS :These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

AT-ONE THUMBHOLE, SAVAGE 11FXP3 TOP BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release.The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock or a plastic stock with a molded in magwell, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.