Gunstocks

CLASSIC, RUGER AMERICAN RANCH GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information about this kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN CENTERFIRE GEN 2, AR MAG, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear take down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: A relief cut has been added to allow magazine release button clearance. ATTENTION CUSTOMERS: You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimensional differences. they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

SPIKE CAMP THUMBHOLE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

AT-ONE THUMBHOLE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

AT-ONE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

LEFT HAND HERITAGE RUGER AMERICAN CENTERFIRE GEN 2, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 MINI 30 MAGAZINE KIT (part no. A09217) offered on the Accessories page. More information on the 7.62x29 Mini 30 Magazine Kit can be found here: https://www.boydsgunstocks.com/ruger-american-7.62x39-mini-30-magazine-kit. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not a defect.

LH FT REM 7 SA LH STK RH ACT MAG BC COYOTE SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 13/16" Center to Center of Action Screws: 5 15/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Designed for the hinged floor plate Remington Model 7 with Magnum barrel contour. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

PH SAKO 75-1 HUNTER SA DBM FBC COYOTE SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1.042" and Point B = .707"Center to Center of Action Screws: 6.683" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and mag box from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Non-refundable & non-returnable.

A black anodized, aluminum bottom metal and trigger guard with a polished steel to allow for a tight grasp on the magazine release button. Instructions and all necessary parts will be provided. The bottom metal kit allows Ruger American rifles to use of the Ruger Mini 30 magazines for the 7.62x39 caliber when they are assembled to a Boyds stock. ATTENTION CUSTOMERS: Critical to start both screws before tightening to final torque (30 in LBS). Learn more about this kit here: Ruger American 7.62x39 Mini 30 Magazine Kit

Traditions Vortek Pistol Grip Stock Overall length 13 8/16" Top Tang width 14/16" Top Tang Length 1 4/16" Stock Height at Receiver 1 6/16" Stock Width at Receiver 1 6/16"ATTENTION CUSTOMERS: You will need your factory receiver mounting bolt, measuring 4 5/16". ATTENTION CUSTOMERS: This inlet is for the older model firearm with a removable trigger guard; newer models have the trigger guard molded into the stock and are incompatible. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Traditions Vortek MUZZLELOADER FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Rear 1" Barrel Channel Front 15/16" Receiver Edge to Center of Mounting Screw 3 4/16" Over All Length of Part: 10 12/16" ATTENTION CUSTOMERS: You will need your ramrod retention clip and screw as well as the forend takdown screw from the factory original. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RVT RVT MARLIN 925 MAGAZINE FEED BBC BLAZE HIGH GLOSS BOYDS PAD ATTENTION CUSTOMERS: WOOD IS SPLINGTING IN VENTED BARREL CHANNEL WINDOW, DENTED ON BUTT, EXTRA LIGHT BLAZE LAMINATE DYE Barrel Dimensions: Point A = 13/16" and Point B = 13/16"Center to Center of Action Screws: 4 7/8"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: These stocks are designed for inlett trigger guard and floor plate. Variations exist on the safety for this model, minor fitting of safety may be needed. ATTENTION CUSTOMERS: ATTENTION CUSTOMERS:If converting from composite stock to a Boyds hardwood gunstock you will need to purchase the Marlin Rimfire Trigger Guard on the Accessories page, part number A09166.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

LH HERT TIKKA T1X DBM LH STK FBC BLAZE SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: FINISH REPAIR ON RIGHT HAND SIDE OF STOCK HAS DIFFERENT TEXTURE Barrel Dimensions: Point A = 7/8" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Hert Win 70 Sa 1-pc Fp Lh Stk Rh Act Fbc Zz Post 64 GREEN PAINT LIMBSAVER PAD ATTENTION CUSTOMERS: SOMETHING UNDER GREEN PAINT ON RIGHT SIDE OF STOCK BY MAGWELL Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Top Tang Width: 0.968"Top Tang Length: 3.822"Bottom Tang Width: 0.668"Bottom Tang Length: 3.822"Stock Height at Receiver: 1.315"Stock Width at Receiver: 1.165"Overall Length of Stock:13.75"Measurement of Receiver Mounting Bolt: N/ABUTTPLATEIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the take down screw from your factory stock.ATTENTION CUSTOMERS: THIS IS DESIGNED FOR THE 17 HMR CALIBER. NOT COMPATIBLE WITH ANY OTHER CALIBER.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

STRAIGHT GRIP WINCHESTER® 94 WRANGLER STK ZZIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTIONCUSTOMERS: Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 1 1/32" Top Tang Length: 3 7/8" Bottom Tang Width: 9/16" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 5/16" Stock Width at Receiver: 1 3/8" Overall Length of Stock:13 1/4" BOYDS' PLASTIC BUTTPLATE All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Due to variations with this model minor fitting of the receiver may be needed even with these finished parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

NORINCO 92 Stock It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 15/16" Top Tang Length: 3 15/16" Bottom Tang Width: 5/8" Bottom Tang Length: 3 15/16" Stock Height at Receiver: 1 7/16" Stock Width at Receiver: 1 5/16" Overall Length of Stock:13 1/4" Measurement of Receiver Mounting Bolt: N/A Comes with Boyds' plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLAT RUGER GUNSITE SCOUT SA LH STK RH ACT DBM FBC PEPPER SATIN FINISH BOYDS PAD WALNUT GRIP CAP LOP 13 1/4" PILLAR BEDDING ATTENTION CUSTOMERS: FINISH FLAWS, DENTED BY TRIGGER GUARD Barrel Dimensions: Point A = 1 5/32" and Point B = 3/4" Center to Center of Action Screws: 6 45/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: If you are purchasing this stock as a replacement to a Polymer Stocked GSR, you will need to purchase or acquire a bottom metal kit to complete the build. You will need your takedown screws, trigger guard, mag box assembly, forward takedown/mag box retainer, and magazine.ATTENTION CUSTOMERS: We do not machine or provide for the factory threaded cross bolt behind the mag well on this model. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP SAV 93 BOLT ACT CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL BLAZE SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ***Stainless Steel Metal trigger guards are also available: PN 100662. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

This magazine well fits magazines where the latch is part of the magazine. If your Long Action Savage rifle has a plastic stock with the magazine well molded into the stock and not transferable to another stock, you will need this piece to make our stock with a Detachable Magazines fit your rifle. This part is not required for the Savage Axis or Edge rifles.

This magazine well fits magazines where the latch is part of the magazine. If your Short Action Savage rifle has a plastic stock with the magazine well molded into the stock and not transferable to another stock, you will need this piece to make our stock with a Detachable Magazines fit your rifle. This part is not required for the Savage Axis or Edge rifles.