Gunstocks

Barrel Dimensions: Point A = 1 5/16" and Point B = 1 1/16" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 11, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/8" and Point B = 11/16"Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 110 TBR FLAT PLATE, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 10, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE BOX MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212..Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, YUGOSLAVIAN MAUSER 52C, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 45/64" and Point B = 45/64" Center to Center of Action Screws: 2 45/64" Over All Length of Part: 28 1/4" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: We will provide the trigger guard with two screws. You will need the take down screws and magazine plate from the original stock. ATTENTION CUSTOMERS: If the floor plate from your factory stock is not removeable, you will need the purchase a new floorplate from DIProducts(Sav-13069). Due to variations in floorplates it may require removal of material for a flush fit. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, STEVENS 200 TBR, BLIND MAGAZINE, SHORT ACTION, CENTERFIRE, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the STEVENS Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Stevens Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 10, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, YUGOSLAVIAN MAUSER 47, #1 BARREL CONTOUR, FINISHED Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 51/64" and Point B = 51/64" Center to Center of Action Screws: 2 45/64" Over All Length of Part: 28 1/4" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: We will provide the trigger guard with two screws. You will need the take down screws and magazine plate from the original stock. ATTENTION CUSTOMERS: If the floor plate from your factory stock is not removeable, you will need the purchase a new floorplate from DIProducts(Sav-13069). Due to variations in floorplates it may require removal of material for a flush fit. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, STEVENS® 315 YOUTH .51 LR, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 116, AT-ONE THUMBHOLE, TOP BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, YUGOSLAVIAN MAUSER 24, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 55/64" and Point B = 51/64" Center to Center of Action Screws: 6" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect . ATTENTION CUSTOMERS :To assemble you will need to use the two escutcheons and action screws from the original.

AT-ONE THUMBHOLE STEVENS® 315 YOUTH .22 LR, BULL BARREL CHANNEL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 116, AT-ONE THUMBHOLE, TOP BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MAUSER YUGO 48, #1 BARREL CONTOUR, FINISHED Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE B MAG, RH ACTION, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 39/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.