Gunstocks

AT-ONE THUMBHOLE, MARLIN 2000L, SHORT ACTION, FACTORY BARREL CHANNEL, ZZ span>Barrel Dimensions: Point A = 0.816" and Point B = 0.81"Center to Center of Action Screws: 2.88" Over All Length of Part: 30.375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the trigger guard, take down screw & wood screw from your original stock. We will provide a take down screw. Customer will need to remove long take down screw and install it in the rear hole. Then use supplied short take down screw for the fron hole.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 11 TBR, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CZ 557 CARBINE, AT-ONE THUMBHOLE, ONE PIECE FLOOR PLATE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 47/64" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER AMERICAN RIMFIRE 22MAG/17HMR, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 23/32" Center to Center of Action Screws: 3 7/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: You will need the rear magazine block, front magazine block, and takedown screws from your factory stock. We will provide the trigger guard and screw. ATTENTION CUSTOMERS: Not compatible with target model. It is only compatible for plastic/synthetic to wood conversion.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON® 700, SHORT ACTION, DETACHABLE MAG, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN 880 SQ, SHORT ACTION, BULL BARREL CHANNEL, ZZ It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 13/16" and Point B = 13/16"Center to Center of Action Screws: 4 57/64"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and clip. We will provide the trigger guard and screw.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 11 TBR, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. MUST READ: If you have a XP model with a synthetic stock, you will need to purchase the bottom metal component system through Savage or any aftermarket component supplier. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CZ 557, SPORTER, AT-ONE THUMBHOLE, 1-PIECE FLOOR PLATE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 47/64" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect-.

AT-ONE THUMBHOLE, RUGER M77 MKII HAWKEYE, LONG ACTION , FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the LEFT hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

AT-ONE THUMBHOLE, REMINGTON® 700, LONG ACTION, DETACHABLE MAG, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is inlet for the standard factory tapered barrel. These stocks are designed for the Remington 700 right hand long action receiver with factory supplied detachable box magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN® 980, CLIP FEED, BULL BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16"Center to Center of Action Screws: 4 7/8"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: These stocks are designed for inlett trigger guard and floor plate. Variations exist on the safety for this model, minor fitting of safety may be needed. ATTENTION CUSTOMERS:If converting from composite stock to a Boyds hardwood gunstock you will need to purchase the Marlin Rimfire Trigger Guard on the Accessories page, part number A09166.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 11 TBR, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CZ® 527, AMERICAN, AT-ONE THUMBHOLE, SHORT ACTION, CLIP FEED, LH ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 0.99" and Point B = 0.885"Center to Center of Action Screws: 5.5" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION: THIS STOCK IS NOT COMPATIBLE WITH THE CZ 527 M CARBINE MODEL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER M77 MKII HAWKEYE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON® 700 BDL, SHORT ACTION, FACTORY BARREL CHANNEL, LH ACTION, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory barrel channel. This stock is designed for the Remington 700 LEFT Hand Short Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, MARLIN® XT-17, CLIP FEED, BULL BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16"Center to Center of Action Screws: 4 7/8"Over All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: These stocks are designed for inlett trigger guard and floor plate. Variations exist on the safety for this model, minor fitting of safety may be needed.ATTENTION CUSTOMERS: You will need your takedown screws, trigger guard, and screw from your original stock. ATTENTION CUSTOMERS:If converting from composite stock to a Boyds hardwood gunstock you will need to purchase the Marlin Rimfire Trigger Guard on the Accessories page, part number A09166.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 11 TBR, BLIND MAGAZINE, SHORT ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

CZ 527 AMERICAN, AT-ONE THUMBHOLE, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 63/64" and Point B = 45/64" Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION: THIS STOCK IS NOT COMPATIBLE WITH THE CZ 527 M CARBINE MODEL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, RUGER M77 MKII HAWKEYE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, REMINGTON® 700 BDL, LONG ACTION, FACTORY BARREL CHANNEL, LH ACTION, FINSHED Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 LEFT Hand Long Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.