Gunstocks

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 63/64” and Point B = 63/64”Over All Length of Part: 31 1/2”Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: You will need the takedown screws from the original stock. We will be providing the trigger guard and trigger guard screws.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Receiver Face to Head of Mounting Screw: 3 55/64"Diameter of Through Hole: 5/16"Width of Trigger Guard: 31/64" Over All Length of Part: 4 35/64" ATTENTION CUSTOMERS: This grip was built off a WASR-10. You will need the mounting screw and threaded receiver block. We will provide the washer for the mounting screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 3/4" and Point B = 23/32"Over All Length of Part: 30 3/8"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, TIKKA M595, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the floor plate, magazine, takedown screws, and takedown screws head washers. We will be providing the lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 23/32" Center to Center of Action Screws: 6 59/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: Our stocks do not utilize the handguard, the upper receiver tang, or the rear floor plate tang brackets. Drop set for scope mount use. The barrel channel is cut for the original military barrel. You will need your floor plate with takedown screws. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut in our stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 3/4" and Point B = 23/32"Over All Length of Part: 30 3/8"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 7/16" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the floor plate, magazine, takedown screws, and takedown screws head washers. We will be providing the lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 23/32" Center to Center of Action Screws: 6 59/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: Our stocks do not utilize the handguard, the upper receiver tang, or the rear floor plate tang brackets. Drop set for scope mount use. The barrel channel is cut for the original military barrel. You will need your floor plate with takedown screws. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut in our stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 17/64" and Point B = 23/32"Center to Center of Action Screws: 6 43/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and mag box from the original stock.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 30 3/8" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the floor plate, magazine, takedown screws, and takedown screws head washers. We will be providing the lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 23/32" Center to Center of Action Screws: 6 59/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: Our stocks do not utilize the handguard, the upper receiver tang, or the rear floor plate tang brackets. Drop set for scope mount use. The barrel channel is cut for the original military barrel. You will need your floor plate with takedown screws. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut in our stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the floor plate, magazine, takedown screws, and takedown screws head washers. We will be providing the lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 23/32" Center to Center of Action Screws: 6 59/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: Our stocks do not utilize the handguard, the upper receiver tang, or the rear floor plate tang brackets. Drop set for scope mount use. The barrel channel is cut for the original military barrel. You will need your floor plate with takedown screws. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut in our stock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 17/64" and Point B = 23/32"Center to Center of Action Screws: 6 43/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and mag box from the original stock.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.09" and Point B = 0.95"Center to Center of Action Screws: Single Takedown Screw" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:______________. You will need the Ram Rod Tension Spring & Trigger Guard from your factory stock. We will provide Black Escutcheon.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:You will need the floor plate, magazine, takedown screws, and takedown screws head washers. We will be providing the lug. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.09" and Point B = 0.95"Center to Center of Action Screws: Single Takedown Screw" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:______________. You will need the Ram Rod Tension Spring & Trigger Guard from your factory stock. We will provide Black Escutcheon.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Channel Point at Rear: 1 19/64" Barrel Channel Point at Front: 7/8" Magazine Tube Width: 1 5/64" Receiver Face to Barrel Mounting Shoulder: 8 11/64" Over All Length of Part: 8 7/8" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your forend spring washers from your stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.09" and Point B = 0.95"Center to Center of Action Screws: Single Takedown Screw" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:______________. You will need the Ram Rod Tension Spring & Trigger Guard from your factory stock. We will provide Black Escutcheon.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 17/64" and Point B = 23/32"Center to Center of Action Screws: 6 43/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need the floor plate, takedown screws, and mag box from the original stock.All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.