Gunstocks

LH FT RUGER AMERICAN RANCH LH ACT LH STK LONG ACTION FBC Maroon Satin Finish Boyds Pad ATTENTION CUSTOMERS: chip by reinforcement pin and gouged on top of comb. Barrel Dimensions: Point A = 1 3/16" and Point B = 12/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. You will need the magazine, as we will not be providing this.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with A1 or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH SAV 10 TBR BLIND MAGAZINE, SHORT ACTION, STAGGERED FEED, FACTORY BARREL CHANNEL Applejack High Gloss Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. All Rapid Fire Sales are final! Nonrefundable & nonreturnable.

Stock Height at Receiver 1 3/4" Stock width at receiver 1 1/2", overall length of part 12 1/4". Measurement of receiver mounting bolt 11". We will provide the washer for your mounting bolt. Attention customers: you will need the nut from your factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill are not considered a defect.

Mossberg 935, 12 Gauge Forend Barrel Channel Point at Rear: 1.115" Barrel Channel Point at Front: 0.875" Receiver Edge to Center of Mounting Screw: N/A" Magazine Tube Width: 1.05" Center to Center of Mounting Screws: N/A" Magazine Tube Shoulder to Shoulder: 1.105" Over All Length of Part: 11.125" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : Customers will need the magazine cap from the factory forend. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Stock Height at Receiver 1 3/4" Stock width at receiver 1 1/2", overall length of part 12 1/4". Measurement of receiver mounting bolt 11". We will provide the washer for your mounting bolt. Attention customers: you will need the nut from your factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill are not considered a defect.

Stock Height at Receiver 1 3/4" Stock width at receiver 1 1/2", overall length of part 12 1/4". Measurement of receiver mounting bolt 11". We will provide the washer for your mounting bolt. Attention customers: you will need the nut from your factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill are not considered a defect.

Stock Height at Receiver 1 3/4" Stock width at receiver 1 1/2", overall length of part 12 1/4". Measurement of receiver mounting bolt 11". We will provide the washer for your mounting bolt. Attention customers: you will need the nut from your factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill are not considered a defect.

Stock Height at Receiver 1 3/4" Stock width at receiver 1 1/2", overall length of part 12 1/4". Measurement of receiver mounting bolt 11". We will provide the washer for your mounting bolt. Attention customers: you will need the nut from your factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill are not considered a defect.

Barrel Dimensions: Point A = 1 1/8" and Point B = 11/16"Center to Center of Action Screws: 7 13/16"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BROWNING BAR TYPE 2 FOREND Walnut Satin Finish It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 17/64" Barrel Channel Point B: 3/4" Receiver Edge to Center of Mounting Screw: 9 7/32" Over All Length of Part: 13" ATTENTION CUSTOMERS :You will need the original swivel stud mounting screw. We will be providing the bushing/spacer where the swivel stud mounts to the gun. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

CLASSIC CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE CVA CASCADE XT DBM LONG ACTION FACTORY BARREL CHANNEL Barrel Channel Dimensions: Point A -where barrel meets receiver - 1 4/16" Point B 9" forward of Point A - 13/16" Center to Center Action Screws: 5 6/16" It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will be required to remove the mag box retention clip from factory stock and install onto Boyds stock. You will need your factory barreled action, floorplate, action screws, mag box, mag box retainer clip with screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/64" and Point B = 0.75"Center to Center of Action Screws: 7.5" Over All Length of Part: 31.5."Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, magazine, takedown screws, and takedown screws head washers. Boyds will provide the recoil lug plate in the stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.143" and Point B = 0.766"Center to Center of Action Screws: 7.465" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This inlet is for the Model 70 Pre WWII model. There are differences between the model 70 pre WWII and the Model 70 Pre 64. Most notable is that the Pre WWII has a clover leaf rear tang on the receiver. You must identify which model you have prior to ordering. You will need take down screws and 2 piece floor plate from the factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.085" and Point B = .715"Center to Center of Action Screws: 6.867" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, take down screws and mag well from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.140" and Point B = 0.680"Center to Center of Action Screws: 8.105" Over All Length of Part: 32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.ATTENTION CUSTOMERS:You will need the floorplate and action screws from your original stock. ATTENTION CUSTOMERS: These stocks are designed for rifles with a 6 lug bolt, and are not compatible with rifles with a 9 lug bolt system.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LH FT SAV 11 BOLT ACT SHORT ACTION, BLIND MAGAZINE, LEFT HAND STOCK, RIGHT HAND ACTION, BULL BARREL CHANNEL Pepper Satin Finish Limbsaver Pad Barrel Dimensions: Point A = 1.310" and Point B = .930"Center to Center of Action Screws: 4.415" Over All Length of Part: 31.50"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need take down screws, and trigger guard & screw from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA RUGER ACF PREDATOR SA LH STK RH ACT DBM FBC Black Jack Satin Finish Boyds Pad ATTENTION CUSTOMERS: rough fin top comb Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION: Not compatible with 7.62x39 caliber due to steel mag liner. Not compatiable with AR mag.ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Barrel Dimensions: Point A = 1.302" and Point B = .97"Center to Center of Action Screws: 4.415"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the take down screws, trigger guard and screw and spring for ram rod from your factory stock. There are two variations of the Savage 10 ML II(2).  You MUST verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, SAKO MAUSER LR, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Length of Floor Plate 8 11/16" Over All Length of Part: 31 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour Barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, SAKO MAUSER LR, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT SAVAGE® 11 BOLT ACTION, SHORT ACTION, BLIND MAGAZINE, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1.310" and Point B = .930"Center to Center of Action Screws: 4.415" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need take down screws, and trigger guard & screw from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 700 PTG, SHORT ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1.25" and Point B = .75"Center to Center of Action Screws: 6.5"Over All Length of Part: 30.375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This inlet is designed to accept PTG short action flushmount detachable mag bottom metal with M5 footprint .;;You will need to purchase the PTG floor plate separately from PTG.; Please ;visit the PTG website for any of the following part numbers:; 30183fe1, p5659618. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 700, LONG ACTION, 1PC HINGED FLOOR PLATE, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1.245" and Point B = 0.9"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT MARLIN® 981T BOLT, SHORT ACTION, TUBE FEED, FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 0.733" and Point B = 0.741"Center to Center of Action Screws: 4.89" Over All Length of Part: 27.00"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need take down screws from the factory stock. We will provide trigger guard and screw.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FT Sears 53 SA 2-PC FP FBC Pepper High Gloss Limbsaver Pad Laser Panel Pillar Bedding LOP 14 3/4" Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. THIS STOCK WILL NOT WORK FOR THE WSSM CALIBER RIFLES. PRE 1984 ACTIONS ARE BASED ON THE LONG ACTION RECEIVER. THESE STOCKS ARE DESIGNED FOR THE WINCHESTER® MODEL 70 SHORT ACTION 2-PIECE HINGED FLOOR PLATE MODEL, WITH STANDARD FACTORY TAPERED BARREL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. All Rapid Fire sales are final! Nonrefundable & Nonreturnable.

FT ITHACA LSA-65 DBM LA FBC Nutmeg Satin FInish Boyds Pad Pillar Bedding LOP 13 1/4" Attention Customers: chips arounds pillar bottom of inlet Barrel Channel Dimensions - Point A: 1 1/16" Point B: 3/4" Center to Center Action Screws: 7 1/16" ATTENTION CUSTOMERS: This stock is not compatible with the Tikka M65A. ATTENTION CUSTOMERS: You will need your factory Floor Plate, Action Screws, Trigger Guard, Trigger Guard Screw, Mag Box Release Tab with Spring, and Mag Box. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PRO VARMINT CZ® 527 AMERICAN, SHORT ACTION, CLIP FEED, LH ACTION, BULL BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 0.99" and Point B = 0.885"Center to Center of Action Screws: 5.5" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION: THIS STOCK IS NOT COMPATIBLE WITH THE CZ 527 M CARBINE MODEL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT CZ® 452 2E AMERICAN BOLT, SHORT ACTION, CLIP, FACTORY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = .99" and Point B = .712"Center to Center of Action Screws: 3.235"Over All Length of Part: 27"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, trigger plate and clip from the factory stock. ATTENTION CUSTOMERS: Not compatible with ZKM model variations. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect."

PRO V CF MOSSBERG® PATRIOT BOLT SA DBM FBC Barrel Dimensions: Point A = 1.175" and Point B = .735"Center to Center of Action Screws: 4.715"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the mag insert, mag box and take down screws from your factory stock. We will provide a metal trigger guard, rear action screw and wood screw.ATTENTION CUSTOMERS: Mossberg Patriot SA AI Mag Assembly kits are available on the Accessories page, Part# A09164. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Pro Varmint, Mossberg® Patriot Bolt, Long Action, Detachable Box Magazine, Factory Barrel Channel Barrel Dimensions: Point A = 1.335" and Point B = 0.74"Center to Center of Action Screws: 5.225"Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the Mag Insert, Mag Box, Take Down Screws from your factory stock.  We will provide a Metal Trigger Guard, Rear Action Screw, and Wood Screw.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP SMITH & WESSON I BOLT LA FBC Nutmeg Satin FInish Boyds Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1-1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Overall Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 right hand long action hinged floor plate models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.