Gunstocks

STEVENS® 311, 20 GA SPLINTER, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 7 1/2" Over All width at receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

WORTHINGTON DBL 16 GA SEMI BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 3/4" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.143" and Point B = 0.766"Center to Center of Action Screws: 7.465" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This inlet is for the Model 70 Pre WWII model. There are differences between the model 70 pre WWII and the Model 70 Pre 64. Most notable is that the Pre WWII has a clover leaf rear tang on the receiver. You must identify which model you have prior to ordering. You will need take down screws and 2 piece floor plate from the factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel at Receiver: Approximately 1" Barrel Channel at End: 11/16" Receiver Edge to Center of Mounting Screw: 6 7/8" Shoulder to Shoulder: 6 11/16" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DBL 16 GA BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 7/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

WINCHESTER® 61 STK ZZ Top Tang width - 3/8" Top Tang length - 15/16" Bottom Tang width - 9/16" Bottom Tang length - 15/16" Stock height at receiver - 1 7/32"" Stock width at receiver - 1 5/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Boyds' model has 17 grooves on forend. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 13/16" Barrel Channel Point B: 13/16" Receiver Edge to Center of Mounting Screw: 1 1/8" Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 8 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.143" and Point B = 0.766"Center to Center of Action Screws: 7.465" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This inlet is for the Model 70 Pre WWII model. There are differences between the model 70 pre WWII and the Model 70 Pre 64. Most notable is that the Pre WWII has a clover leaf rear tang on the receiver. You must identify which model you have prior to ordering. You will need take down screws and 2 piece floor plate from the factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, WINCHESTER® 70, LH STOCK, RH ACTION, SHORT ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DBL 20 GA SPLINTER, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 7 1/2" Over All width at receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

WORTHINGTON DBL 20 GA SEMI BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 3/4" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

WORTHINGTON DBL 20 GA BEAVERTAIL, FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All width at receiver: 1 7/8" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.

Barrel Dimensions: Point A = 1.143" and Point B = 0.766"Center to Center of Action Screws: 7.465" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This inlet is for the Model 70 Pre WWII model. There are differences between the model 70 pre WWII and the Model 70 Pre 64. Most notable is that the Pre WWII has a clover leaf rear tang on the receiver. You must identify which model you have prior to ordering. You will need take down screws and 2 piece floor plate from the factory stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester? Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WINCHESTER® XTR 20 GA STOCK, ZZ All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WORTHINGTON DBL 12 GA SPLINTER FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A" Barrel Channel Point B: N/A" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 7 1/2" Over All width at receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Final fitting of spring clip assembly and drilling for mounting screws maybe required due to the many variations of mounting hardware used on this model.