Gunstocks

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release (located on the side of the receiver). Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Top Tang Width: n/a"Top Tang Length: n/a"Bottom Tang Width: n/a"Bottom Tang Length: n/a"Stock Height at Receiver: 2.1"Stock Width at Receiver: 1.4"Overall Length of Stock:12.5"Measurement of Receiver Mounting Bolt: 5.5"Vented BUTTPLATEIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:We will provide 3/8" washer.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Channel Point at Rear: 1.254"Barrel Channel Point at Front: .99"Receiver Edge to Center of Mounting Screw: N/A"Magazine Tube Width: 1.14"Center to Center of Mounting Screws: N/A"Magazine Tube Shoulder to Shoulder: 5.07"Over All Length of Part: 9.115"It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Customer will need the forend cap nut from the factory forend.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

STEVENS® 940E 12 GA SPRING CLIP SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/32" Barrel Channel Point B: 11/16" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A Over All Length of Part: 9" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: No mounting hardware is included. This forend is for internal mounted springclip. Variations of mounting hardware exist, fitting of your hardware may be needed.

STEVENS® 77C 12GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A" Top Tang Length: N/A" Bottom Tang Width: 3/4" Bottom Tang Length: 5/16" Stock Height at Receiver: 2 7/16" Stock Width at Receiver: 1 11/32" Overall Length of Stock:13 1/4" Measurement of Boyds'Receiver Mounting Bolt: 5 1/2" BUTTPLATE ATTENTION CUSTOMERS:Known variations exist on this model you need to confirm supplied dimensions with your firearm . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1" Barrel Channel Point B: 1" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws: 5" Over All Length of Part: 11" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Many variations in mounting screws exist, if your factory screw set does not fit you will need to contact an aftermarket hardware supplier.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 15/16" Receiver Edge to Center of Mounting Screw: 4 1/8" Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:If you have exposed metal mounting plate, see the Savage 94 spring clip or take down forend for possible compatability.

STEVENS® 107 SINGLE 12GA FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 7/8" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All Width at Receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Many variations exist, also see the Savage 94 Forends for possible compatibility.

SAVAGE® 94 .410 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 15/16" Receiver Edge to Center of Mounting Screw: 4 1/8" Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:If you have exposed metal mounting plate, see the Savage 94 spring clip or take down forend for possible compatibility

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1" Barrel Channel Point B: 3/4" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws: 5" Over All Length of Part: 11" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: Many variations in mounting screws exist, if your factory screw set does not fit you will need to contact an aftermarket hardware supplier.

STEVENS® 940DY 20 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.

STEVENS® SINGLE 12GA FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 7/8" Receiver Edge to Center of Mounting Screw/Magazine Tube Width: N/A" Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9" Over All Width at Receiver: 1 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:Many variations exist, also see the Savage 94 Forends for possible compatibility.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Overall Length of Stock:14 1/4"Measurement of Receiver Mounting Bolt: 2"All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:Encore stocks are designed for the 2 inch long action screw.Some models will require you to purchase new action screw to secure your action to Boyds' stock. You may be able to purchase direct from TCA or Brownells.