Gunstocks

Barrel Dimensions: Point A = 63/64" and Point B = 47/64" Center to Center of Action Screws: 7.46" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS :You will need the washer from the factory rear take down screw for the new rear take down screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad. This is for the side release magazine version of a synthetic stock. If you have a wooden stock, it will require fitting and a different trigger guard. ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 55/64" and Point B = 51/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS:  To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed.  We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel.

PRO VARMINT, SAVAGE B-MAG, DETACHABLE BOX MAGAZINE, SHORT ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 51/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS: To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. ;We will provide you with a black plastic trigger guard.;It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect . ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.

Barrel Dimensions: Point A = 63/64" and Point B = 47/64" Center to Center of Action Screws: 7.46" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS :You will need the washer from the factory rear take down screw for the new rear take down screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 11/64" and Point B = 31/32"Center to Center of Action Screws: 5 1/16"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, mag box, and trigger guard with screw. ATTENTION CUSTOMERS:ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 12 GAUGE shotgun shell. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

Barrel Dimensions: Point A = 63/64" and Point B = 47/64" Center to Center of Action Screws: 7.46" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS :You will need the washer from the factory rear take down screw for the new rear take down screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 11/64" and Point B = 31/32"Center to Center of Action Screws: 5 1/16"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, mag box, and trigger guard with screw. ATTENTION CUSTOMERS:ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 12 GAUGE shotgun shell. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel.

Barrel Dimensions: Point A = 55/64" and Point B = 51/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS:  To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed.  We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 11/64" and Point B = 31/32"Center to Center of Action Screws: 5 1/16"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, mag box, and trigger guard with screw. ATTENTION CUSTOMERS:ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 12 GAUGE shotgun shell. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:These stocks are designed for the Long Action 1 piece floor plate design with standard factory tapered barrel. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE A17, SEMI-AUTO, AT-ONE, DETACHABLE BOX MAGAZINE, BULL BARREL CHANNEL Barrel Dimensions: Point A = 0.92" and Point B = 0.765" Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: We provide the T-nut sert and mag tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.