Gunstocks

Barrel Dimensions: Point A = 55/64" and Point B = 51/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS:  To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed.  We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.

Barrel Dimensions: Point A = 1.302" and Point B = .970"Center to Center of Action Screws: 4.27" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:There are two variations of the Savage 10 ML II. You must verify the hole to hole dimensions of the take down screws to insure you are ordering the correct version. You will need the take down screws, trigger guard & screw, spring for ram rod from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE SAVAGE® 110 1ST GEN BLIND MAG SHORT ACTION LEFT HAND ACTION FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: We provide the T-nut sert and mag tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 11/64" and Point B = 31/32"Center to Center of Action Screws: 5 1/16"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, mag box, and trigger guard with screw. ATTENTION CUSTOMERS:ATTENTION CUSTOMERS : This is for the older style floor plate that measures 5.7875. The gun is chambered for a 12 GAUGE shotgun shell. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND HERITAGE SAVAGE® 110 1ST GEN BLIND MAG SHORT ACTION LEFT HAND ACTION LEFT HAND STOCK FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, SAVAGE 110 TBR FLAT PLATE, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, SAVAGE B MAG, LH STOCK, RH ACTION, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 39/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.

HERITAGE, SAVAGE 110 TBR FLAT PLATE, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE A17 SEMI-AUTO, HERITAGE, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: We provide the T-nut sert and mag tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PRAIRIE HUNTER SAVAGE® 110 1ST GEN BLIND MAG SHORT ACTION LEFT HAND ACTION LEFT HAND STOCK FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, SAVAGE, B-MAG, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 39/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS:  To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard.;It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

LEFT HAND FEATHERWEIGHT THUMBHOLE SAVAGE® 110 1ST GEN BLIND MAG SHORT ACTION LEFT HAND ACTION LEFT HAND STOCK FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

PRO VARMINT, SAVAGE 110 TBR FLAT PLATE, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, SAVAGE, B-MAG, LH STOCK, RH ACTION, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 55/64" and Point B = 39/64"Center to Center of Action Screws: 6"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS: To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:To assemble you will need to use the two escutcheons and action screws from the original.