Gunstocks

STEVENS® 30D (TOP REC SAFETY) STOCK These parts are designed to fit the Savage,Stevens,Springfield and Fox models 30,67,77,79,168 and 176 stocks with top receiver safety, please compare your stock and receiver measurements with those we supply.Make sure to confirm demensions with those supplied for this parts. There may be up to five variations of this model.Top Tang width - 9/16ths"Top Tang length - 1 7/16ths"BottomTang width - 5/8ths"BottomTang length - 1 5/16ths"Stock height at receiver -1 5/8ths"Stock width at receiver -1 1/2" Semi-inlet parts have been comletely shaped and 95% machine inlet. Stocks are rough sanded and unless otherwise specified, are shipped with a BOYDS' butt plate.(SEMI-INLET) stocks do require some knowledge of firearms and woodworking for installation.

STEVENS® 940Y 16 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

STEVENS® 30D (TRIGGER GUARD SAFETY)) STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: N/A Top Tang length: N/A Bottom Tang width: 5/8" Bottom Tang length: 1 3/8" Stock height at receiver: 2" Stock width at receiver: 1 5/16" Overall Length of Stock: 13 3/4" Measurement of Receiver Mounting Bolt: 5 1/4" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

STEVENS® 940Y 12 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

STEVENS® 940E .410 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 15/16" Receiver Edge to Center of Mounting Screw: 4 1/8" Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:If you have exposed metal mounting plate, see the Savage 94 spring clip or take down forend for possible compatability.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release (located on the side of the receiver). Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

STEVENS® 940E 20 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.

STEVENS® 67E 12GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A" Top Tang Length: N/A" Bottom Tang Width: 3/4" Bottom Tang Length: 5/16" Stock Height at Receiver: 2 7/16" Stock Width at Receiver: 1 11/32" Overall Length of Stock:13 1/4" Measurement of Boyds'Receiver Mounting Bolt: 5 1/2" BUTTPLATE ATTENTION CUSTOMERS:Known variations exist on this model you need to confirm supplied dimensions with your firearm . All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/8" Barrel Channel Point B: 15/16" Receiver Edge to Center of Mounting Screw: 4 1/8" Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 1/2" All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:If you have exposed metal mounting plate, see the Savage 94 spring clip or take down forend for possible compatability.

STEVENS® 940E 12 GA TAKEDOWN SINGLE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 3/4 " Magazine Tube Shoulder to Shoulder: N/A Over All Length of Part: 9 " Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: If you do not have spring clip model forend please see the savage 94 takedown or Stevens model 85 for possible compatible parts.