Gunstocks

SAVAGE® 311 TYPE 2 12 GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/4" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE® 820, 12 GA, RIBBED FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

BARRACUDA, SAVAGE® 93E MKII Barrel Dimensions: Point A = 13/16" and Point B = N/A Center to Center of Action Screws: 3 11/16" Over All Length of Part: 28 1/4" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, SAVAGE 111 TBR, BLIND MAGAZINE, LONG ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on the Accessories page, left hand side at the bottom of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside of the stock when the barreled action is removed. If the magazine box stays attached to the action you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE, SAVAGE 114, TOP BOLT RELEASE, BLIND MAGAZINE, LONG ACTION ,STAGGERED FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on the Accessories page, left hand side at the bottom of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release.When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 11, PLATINUM, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, SAKO L579 FORESTER, SHORT ACTION ,FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/64" and Point B = 49/64" Center to Center of Action Screws: 6 7/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, SAVAGE 16 TBR, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, SAVAGE 116 TOP BOLT RELEASE, BLIND MAGAZINE, STAGGERED FEED, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page, bottom left hand side of the website. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release.When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1"Center to Center of Action Screws: 4 9/32"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release.When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer.Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER AMERICAN RANCH, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, triggerguard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE® 621 (TOP REC SAFETY) 12 GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: 5/8" Top Tang length: 1 3/8" BottomTang width: 5/8" BottomTang length: 1 3/8" Stock height at receiver: 1 9/16" Stock width at receiver: 1 3/8" Overall Length of Stock: 13 1/4" Measurement of Receiver Mounting Bolt: 4 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

SAVAGE® 3151 ST, TYPE 1, 12GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, SAVAGE 10 TBR, DETACHABLE MAGAZINE, SHORT ACTION, LH STOCK, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE® 311 TYPE 1 12GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: 5/8" Top Tang Length: 3 1/8" Bottom Tang Width: 5/8" Bottom Tang Length: 3 7/8" Stock Height at Receiver: 1 7/8" Stock Width at Receiver: 1 5/8" Boyds' Black Plastic Buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE® 820, 12 GA, RIBBED FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, SAVAGE 114, TOP BOLT RECEIVER, BLIND MAGAZINE, LONG ACTION , STAGGERED FEED, LH STOCK, RH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on the Accessories page, left hand side at the bottom of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

SS EVOLUTION®, SAVAGE® 93E MKII Barrel Dimensions: Point A = 13/16" and Point B = N/ACenter to Center of Action Screws: 3 11/16"Over All Length of Part: 27" w/padComes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.