Gunstocks

AT-ONE, SAVAGE 111 TBR, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate.Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

HERITAGE, RUGER® MINI 30, LEFT HAND STOCK Barrel Dimensions: Point A = 29/32" and Point B = 5/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need the factory trigger assembly, magazine, forend liner, and cap assembly from your original stock. Our inlet is designed not to use the stock reinforcement or side stock reinforcement screws. There will not be swivel studs installed on the forend. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, SAKO MAUSER LR, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, SAVAGE® 93R, BULL BARREL CHANNEL, STOCK, ZZ Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the receiver) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE® 620A, 12 GA, RIBBED FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, SAVAGE 14 TBR, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release (located on the side of the receiver). Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMIT THUMBHOLE, SAKO A7-M, DETACHABLE BOX MAGAZINE, LONG ACTION Barrel Dimensions: Point A = 1 1/8" and Point B = 23/32" Center to Center of Action Screws: 7 41/64" Over All Length of Part: 31 7/16" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: You will need your floor plate, takedown screws, and magazine. We will provide the recoil lug. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, SAVAGE 110 TBR, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, SAVAGE 111 TBR, DETACHABLE MAGAZINE, LONG ACTION, LH STOCK, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PLATINUM, RUGER® MINI 30, LEFT HAND STOCK Barrel Dimensions: Point A = 29/32" and Point B = 5/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need the factory trigger assembly, magazine, forend liner, and cap assembly from your original stock. Our inlet is designed not to use the stock reinforcement or side stock reinforcement screws. There will not be swivel studs installed on the forend. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE, SAKO MAUSER LR, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16"Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RIMFIRE VARMIT THUMBHOLE, SAVAGE® 93R, BULL BARREL CHANNEL STOCK Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the receiver) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE® 620A, 12 GA, RIBBED FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: N/A Barrel Channel Point B: N/A Magazine Tube Width: 1 1/8 Magazine Tube Shoulder to Shoulder: 4 1/2 Over All Length of Part: 6 3/4 All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, SAVAGE 14 TBR, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, SAVAGE 110 TBR, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, SAVAGE 111 TBR, DETACHABLE MAGAZINE, LONG ACTION, LH STOCK, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate.Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

PRO VARMINT, SAKO MAUSER LR, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16"Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, RUGER® MINI 30 Barrel Dimensions: Point A = 29/32" and Point B = 5/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need the factory trigger assembly, magazine, forend liner, and cap assembly from your original stock. Our inlet is designed not to use the stock reinforcement or side stock reinforcement screws. There will not be swivel studs installed on the forend. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RIMFIRE HUNTER, SAVAGE® 93R, BULL BARREL CHANNEL, STOCK, ZZ Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 27" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the receiver) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee.

FEATHERWEIGHT THUMBHOLE, SAVAGE 14 TBR, BLIND MAGAZINE, SHORT ACTION ,CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.