Gunstocks

RUGER 22 CHARGER PISTOL ANY BARREL CONTOUR It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = .920" Over All Length of Part: 15" ATTENTION CUSTOMERS:You will need the takedown screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, RUGER 77 MKII, LONG ACTION, LEFT HAND STOCK, LEFT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the LEFT hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE, PERUVIAN MAUSER 1935, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16"Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RANGER® 120, 20GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: N/A Top Tang length: N/A Bottom Tang width: N/A Bottom Tang length: N/A Stock height at receiver: 2 1/8" Stock width at receiver: 1 7/16" Overall Length of Stock: 13 1/4" Measurement of Receiver Mounting Bolt: 5 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. ATTENTION CUSTOMERS: These stocks are designed for the V notch receiver.

BARRACUDA RUGER® 10/22® MAG, ANY BARREL CONTOUR Barrel Dimensions: Point A = .920" and Point B = N/A Center to Center of Action Screws: N/A Over All Length of Part: 28 1/4" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Comes with brass mounting escutcheon. This stock is designed for the factory Ruger 10/22 Magnum Semi-Auto Action, measuring 6 3/4" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, REMINGTON 700 XCR, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 6 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Short Action with hinged floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, REMINGTON® 788, LONG RECEIVER, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16"Center to Center of Action Screws: 7"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Remington 788 Long Action. Long action Calibers- 243 Win, 6mm Rem, 7mm-08 Rem, 308 Win.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, REMINGTON 700 SPS, LONG ACTION ,FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Overall Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 right hand long action hinged floor plate models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, RUGER M77 MKII, LONG ACTION, LEFT HAND STOCK, LEFT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the LEFT hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE, REMINGTON® 710, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions:where barrel meets reciever/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 diffrent types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.:All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC REMINGTON 78 ADL, SHORT ACTION ,FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 6 1/2"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is inlett for standard factory tapered barrel channel and is designed for the Remington 700 right hand short action with blind magazine, loads and unloads through top of action.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, RUGER 77 MKII, SHORT ACTION, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up.ATTENTION CUSTOMERS: Some WSM calibers may require modifications to the magwell due to the width in the magazine sleeve in the firearm. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE, RUGER 77/22 HORNET, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 59/64" and Point B = 43/64" Center to Center of Action Screws: 7 9/16" Lower Magazine Opening Length: 2 3/64" Over All Length of Part: 31 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT , PERUVIAN MAUSER 1935, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16"Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

RANGER® 120, 16GA STOCK It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang width: N/A Top Tang length: N/A Bottom Tang width: N/A Bottom Tang length: N/A Stock height at receiver: 2 1/8" Stock width at receiver: 1 7/16" Overall Length of Stock: 13 1/4" Measurement of Receiver Mounting Bolt: 5 1/2" Comes with Boyds' black plastic buttplate All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. ATTENTION CUSTOMERS: These stocks are designed for the V notch receiver.

SS EVOLUTION®, RUGER® 10/22® MAG, ANY BARREL CONTOUR, FINISHED Barrel Dimensions: Point A = .920" and Point B = N/A Center to Center of Action Screws: N/A Over All Length of Part: 27" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Comes with brass mounting escutcheon. This stock is designed for the factory Ruger 10/22 Magnum Semi-Auto Action, measuring 6 3/4" long. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE, REMINGTON 788, LONG RECEIVER, LEFT HAND STOCK, RIGHT HAND ACTION, FBC Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16"Center to Center of Action Screws: 7"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Remington 788 Long Action.Long action Calibers- 243 Win, 6mm Rem, 7mm-08 Rem, 308 Win.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM, REMINGTON 700 SPS, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Overall Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 right hand long action hinged floor plate models. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, RUGER M77 MKII, LONG ACTION, LEFT HAND ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 MKII rifles with safety located by the bolt handle on the right hand side of the action. If you have the rear mounted safety, please see the Ruger 77 tang safety models. Our inlet is designed for Standard Short Action calibers, Magnum calibers will require the magazine well to be opened up. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

STERLING LH REMINGTON® 76 STOCK Stock comes with mounting bolt.It is your responsibility to confirm the dimensions o(FINISHED)your firearm with the supplied dimensions o(FINISHED)our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 9/16"Stock Height at Receiver: 1 13/16"Stock Width at Receiver: 1 5/16"Overall Length o(FINISHED)Stock: 14"Measurement o(FINISHED)Receiver Mounting Bolt - 8 5/16"Comes with Pachmayr Decelerator recoil padBoyds inlets (both butt and fore end) for the Remington 870, 20 gauge are for the Lightweight version. Remington also produced/produces the 870, 20 gauge on the 12 gauge frame. If you have the 20 gauge version that is built on the 12 gauge frame, you need to order the 12 gauge butt and fore end. If you are unsure of which version you have, contact a qualified gunsmith for assistance.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the smaller frame models.