Gunstocks

WINCHESTER 70 COYOTE, LONG ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :These stocks are designed for the Long Action 2 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE STEVENS® 300, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Variations in action mounting screw pillars exist between models. Do not over tighten. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP, SAVAGE 111 TROPHY HUNTER, TOP BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, LH STOCK Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE STEVENS® 300 BULL BARREL CHANNEL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE 111 TROPHY HUNTER TOP BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS :These stocks are designed for the Long Action 1 piece floor plate design with standard factory tapered barrel. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 7/8” and Point B = 3/4"Over All Length of Part: 29 3/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE 112 BOLT BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS :These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 3/4" and Point B = 45/64"Over All Length of Part: 29 3/4"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE 112 BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Springfield Model A03, Remington and Smith Corona also made these rifles. The easiest way to tell between the 1903 and 1903 A3 Rifles is to note where the rear sight is located. The 1903 A3 Rifle has a rear sight mounted on the back of the action by the bolt handle and 1903 Rifle has a rear sight mounted in front of the action. The area on the LEFT hand side of the stock is relief for the magazine cut-off on the original rifles. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with handguard. These stocks do not come with a bolt cut. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 12, SPIKE CAMP THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE BOX MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/32" and Point B = 3/4"Center to Center of Action Screws: 4 7/16"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: You will need the takedown screws and trigger guard from the original stock. We will provide the escutcheon.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: The easiest way to tell between the 1903 and 1903 A3 Rifles is to note where the rear sight is located. The 1903 A3 Rifle has a rear sight mounted on the back of the action by the bolt handle and 1903 Rifle has a rear sight mounted in front of the action. The area on the LEFT hand side of the stock is relief for the magazine cut-off on the original rifles. These are Sporter stocks, they are not cut for barrel bands and are not intended to be used with handguard. These stocks do not come with a bolt cut. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE 12, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, WINCHESTER 70, SUPER SHORT ACTION, 1PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: where barrel meets receiver/Point A=1 1/8" Barrel Dimensions: 9 inches in front of Point A/Point B= 11/16" Center to Center of Action Screws: 6 3/8" Attention Customers: Winchester Model 70 Super Short Action One Piece Hinged Floor Plate It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SMITH & WESSON 1700 SHORT ACTION, BULL BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 1" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Short Action, with factory Varmint Contour. Numerous other models have been manufactured using this action design.

SPIKE CAMP THUMBHOLE, SAVAGE 11FXP3 TOP BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release.The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock or a plastic stock with a molded in magwell, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, WINCHESTER 70, SUPER SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: where barrel meets receiver/Point A=1.138" Barrel Dimensions: 9 inches in front of Point A/Point B= .668" Center to Center of Action Screws: 6.35" Attention Customers: Winchester Super Short Magnum-Blind Mag-NO FLOOR PLATE Attention Customers: It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.br

SPIKE CAMP THUMBHOLE, SAVAGE 11FXP3 TOP BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release.The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock or a plastic stock with a molded in magwell, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, WINCHESTER® 70, LH STOCK, RH ACTION, SHORT ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE SMITH & WESSON 1700, LONG ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 3/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Long Action. Numerous other models have been manufactured using this action design.

SPIKE CAMP THUMBHOLE, SAVAGE 11FXP3 TOP BOLT RELEASE, BLIND MAGAZINE, SHORT ACTION, CENTERFEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. Part no. 100010 (Blued) or 100011 (Nickel).This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release.When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

WINCHESTER 70, POST 64, SPIKE CAMP THUMBHOLE, LONG ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:These stocks are designed for the Long Action 2 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE SMITH & WESSON 1500, SHORT ACTION, BULL BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 1" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Short Action, with factory Varmint Contour. Numerous other models have been manufactured using this action design.

SPIKE CAMP THUMBHOLE, SAVAGE 11FXP3 TOP BOLT RELEASE, BLIND MAGAZINE, SHORT ACTION, STAGGERFEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. Part no. 100010 (Blued) or 100011 (Nickel). This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel.

SPIKE CAMP THUMBHOLE SMITH & WESSON 1500, SHORT ACTION, FACTORY BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Short Action, with factory tapered barrel channel. Numerous other models have been manufactured using this action design.

SPIKE CAMP THUMBHOLE, SAVAGE 11FXP3 TOP BOLT RELEASE, BLIND MAGAZINE, SHORT ACTION, CENTERFEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 1 1/16" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. Part no. 100010 (Blued) or 100011 (Nickel). This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:These stocks are designed for the Long Action 1 piece floor plate design with standard factory tapered barrel. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE SMITH & WESSON 1500 LA FBC Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 3/4" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock is designed for the Weatherby Vanguard Long Action. Numerous other models have been manufactured using this action design.

SPIKE CAMP, SAVAGE 11FXP3 TOP BOLT RELEASE, BLIND MAGAZINE, SHORT ACTION, STAGGER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. Part no. 100010 (Blued) or 100011 (Nickel). This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These stocks are designed for the SEARS TW 73 Long Action No floor plate with standard factory tapered barrel.

SPIKE CAMP SAVAGE 11FXP3 TOP BOLT RELEASE, BLIND MAGAZINE, SHORT ACTION, CENTER FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. Part no. 100010 (Blued) or 100011 (Nickel). This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release.When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the SEARS TW 73 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Sears to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks.

SPIKE CAMP THUMBHOLE, SAVAGE AXIS, DETACHABLE BOX MAGAZINE, SHORT ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 1/3" and Point B = 59/64"ATTENTION CUSTOMERS: For short action calibers; 22-250 REM, 223 REM, 243 WIN, 308 WIN, 6.5 Creedmoor, or 7MM-08 REM. When assembling, hold the barrel in the center of the channel and tighten screws.Length of Mag Box: 3 17/64" approximately Center to Center of Action Screws: 4 25/32"Over All Length of Part: 29 3/4"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and the Bolt Release is on the side of the receiver.A black plastic trigger guard, screw, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. Blued Metal trigger guards are also available: PN 10061. They can be found on the Accessories page. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE , WESTERN FIELD MAUSER EJN-757, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SEARS TW 73, SHORT ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBOLE, SAVAGE AXIS, DETACHABLE BOX MAGAZINE, LONG ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/32" and Point B = 23/32" ATTENTION CUSTOMERS: For long action calibers; 25-06 REM, 30-06 SPFLD, or 270 WIN. When assembling, hold the barrel in the center of the channel and tighten screws. Length of Mag Box: 3 49/64" approximately Center to Center of Action Screws: 4 25/32" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. Blued Metal trigger guards are also available: PN 10061. They can be found on the Accessories page.***ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP WESTERN FIELD MAUSER 720-A #1 BC Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Length of Floor Plate 8 11/16" Over All Length of Part: 31 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour Barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

p>SEARS TW 73, SPIKE CAMP THUMBHOLE, LONG ACTION, 2-PC FLOOR PLATE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 7/32" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:These stocks are designed for the Long Action 2 piece hinged floor plate with standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, SAVAGE AXIS, LH ACTION, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 1/32" and Point B = 23/32" ATTENTION CUSTOMERS: For short action calibers; 22-250 REM, 223 REM, 243 WIN, 308 WIN, or 7MM-08 REM. When assembling, hold the barrel in the center of the channel and tighten screws. Length of Mag Box: 3 17/64" approximately Center to Center of Action Screws: 4 25/32" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. A black plastic trigger guard, screw, front mag tab, rear mag tab, and recoil lug are included with the stock. ***Stainless Steel Metal trigger guards are also available: PN 100662. Blued Metal trigger guards are also available: PN 10061. They can be found on the Accessories page.*** ATTENTION CUSTOMERS: This stock is compatible with the Savage Axis II and Axis XP models. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP THUMBHOLE, WESTERN FIELD MAUSER 720, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:This stock will not work for the WSSM caliber rifles. Pre 1984 actions are based on the long action receiver.These stocks are designed for the Short Action 1 piece hinged floor plate with standard factory tapered barrel.