Gunstocks

Barrel Dimensions: Point A = 1 1/32" and Point B = 19/32"Center to Center of Action Screws: 4 13/32"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.This inlet is for the Savage Lightweight Hunter, which is part of the Model 16 Trophy series that utilize the Axis style detachable box magazine and has NO metal frame around the magazine well. The lightweight hunter features lightening cuts in the receiver and a helical fluted bolt, along with a thin profile barrel.ATTENTION CUSTOMERS: YOU WILL NEED the Trigger Guard with Bolt Release Assembly, Action Screws, and Rear Trigger Guard Screw. We will provide the Swivel Studs, Front Magazine Tab, and Rear Magazine Tab.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, TURKISH MAUSER, 1903, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Length of Floor Plate 8 11/16" Over All Length of Part: 31 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour Barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 1 5/64" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. You will need the floor plate, magazine, takedown screws, and takedown screws head washers. Boyds will provide the recoil lug plate in the stock. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 63/64" and Point B = 47/64" Center to Center of Action Screws: 7.46" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS :You will need the washer from the factory rear take down screw for the new rear take down screw. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.182" and Point B = 0.682"Center to Center of Action Screws: 8.035"Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil PadIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: This item is not compatible with detachable magazine models. This item is designs for the hinged floor plate TC Icon model.  You will need Floor Plate & Take Down Screws from your original stock.  WE will provide red safety ball.  All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, TIKKA T3 LITE, DETACHABLE BOX MAGAZINE, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 9/64" and Point B = 55/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. ***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09211*** It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE A17, SEMI-AUTO, AT-ONE THUMBHOLE, DETACHABLE BOX MAGAZINE, BULL BARREL CHANNEL COMPATIBLE WITH THE 17 HMR ONLY - NOT THE 17 WSM.. Barrel Dimensions: Point A = 0.92" and Point B = 0.765" Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: We provide the T-nut sert and mag tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE TC VENTURE DBM SA FBC ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 45/64" Center to Center of Action Screws: 6 29/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your takedown screws and magazine from your original stock. We will be providing the trigger guard, trigger guard screw, and plastic magazine catch.Short Action calibers- 22-250 Rem, 308 Win, 7mm-08 Rem. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: Attention Customer: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE LA PLASTIC MAG WELL, part no. A09160. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 9/64" and Point B = 45/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. ***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09211***It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

SAVAGE A17, SEMI-AUTO, AT-ONE THUMBHOLE, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL COMPATIBLE WITH THE 17 HMR ONLY - NOT THE 17 WSM.. Barrel Dimensions: Point A = 0.92" and Point B = 0.69"Center to Center of Action Screws: 7.444" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: We provide the T-nut sert and mag tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

THOMPSON CENTER VENTURE, AT-ONE THUMBHOLE, DETACHABLE BOX MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 45/64" Center to Center of Action Screws: 7 15/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: You will need your takedown screws and magazine from yout original stock. We will be providing the trigger guard, trigger guard screw, and plastic magazine catch. Long Action Calibers- 270 Win, 300 Win Mag, 30-06 Spfld, 7mm Rem Mag. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, TIKKA T3 LITE, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 9/64" and Point B = 45/64"Center to Center of Action Screws: 7"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.Safety is located on the tang and the Bolt Release is on the side of the receiver.ATTENTION CUSTOMERS: Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical.***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09211***It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.032" and Point B = .710"Center to Center of Action Screws: 5.06" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:This inlet is for rifles that DO NOT have the metal bottom frame/metal around the magazine opening. You will need detachable box mag, 2 take down screws, wood screw, and trigger guard from the factory stock. We will provide escutcheon and front & rear mag clips.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Dimensions: Point A = 3/4” and Point B = 45/64”Over All Length of Part: 27”Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS: This stock will not allow a free floated barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, TIKKA T3, DETACHABLE BOX MAGAZINE, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 9/64" and Point B = 55/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS: Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. ***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09210*** It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE SAVAGE® 110 1ST GEN BLIND MAG SHORT ACTION LEFT HAND ACTION FACTORY BARREL CHANNELBarrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, STEVENS 110 TBR, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the STEVENS Model Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Stevens Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 14 BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 9/64" and Point B = 45/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical.***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09210*** It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE SAVAGE® 110 1ST GENERATION SA BLIND MAG FBC ZZBarrel Dimensions: Point A = 1.028" and Point B = .715"Center to Center of Action Screws: 4.51" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Recoil to front action screw: 1.01" This inlet is for Savage 110 1st Generation Firearms. They are also referred to as "J" series or intermediate models. You will need the take down screws, trigger guard and mag box & spring from your factory stock. .All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside of the stock when the barreled action is removed. If the magazine box stays attached to the action you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 14 BOTTOM BOLT RELEASE, AT-ONE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 9/64" and Point B = 45/64" Center to Center of Action Screws: 7" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical. ***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09210***It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.032" and Point B = .902"Center to Center of Action Screws: 4.415"Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. When you disassemble your action the magazine box will be attached to the receiver. If the magazine box stays inside of the stock when the barreled action is removed, you may need the Center Feed Model or CTF version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 11, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from Savage or Brownells. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:These stocks are designed for the Long Action 1 piece floor plate design with standard factory tapered barrel. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 21/64" and Point B = 23/32"Center to Center of Action Screws: 5 1/16”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  This inlet is for the side release magazine version. You will need your trigger guard with screws and side release button.  All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 1 1/16" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 11, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/8" and Point B = 11/16"Center to Center of Action Screws: 7 13/16" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, SAVAGE 110 TBR FLAT PLATE, BLIND MAGAZINE, LONG ACTION, STAGGERED FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Model Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 9/32" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately in our gun parts section on the LEFT hand side of our webpage. This stock is designed for the Savage Blind Magazine with Staggered Feed action and a top bolt release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect and will be subject to the 12% restocking fee. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 10, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE BOX MAGAZINE, SHORT ACTION, LH ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212..Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, YUGOSLAVIAN MAUSER 52C, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 45/64" and Point B = 45/64" Center to Center of Action Screws: 2 45/64" Over All Length of Part: 28 1/4" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: THIS INLET IS BASED ON THE PRE-2022 SOLID STEEL RECEIVER MODELS. NEW MODELS WILL HAVE A PLASTIC CAP ON THE REAR OF THE RECEIVER AND ARE NOT COMPATIBLE. ATTENTION CUSTOMERS: We will provide the trigger guard with two screws. You will need the take down screws and magazine plate from the original stock. ATTENTION CUSTOMERS: If the floor plate from your factory stock is not removeable, you will need the purchase a new floorplate from DIProducts(Sav-13069). Due to variations in floorplates it may require removal of material for a flush fit. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, STEVENS 200 TBR, BLIND MAGAZINE, SHORT ACTION, CENTERFIRE, FACTORY BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the STEVENS Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Stevens Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 10, AT-ONE THUMBHOLE, BOTTOM BOLT RELEASE, DETACHABLE MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with bottom bolt release (located on the front of the trigger guard). The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. The magazine inletting is designed for the removable frame from the factory stock.ATTENTION CUSTOMERS: If you have an Apex Hunter model it will not be a direct fit in this stock, as it will require modifying the trigger area for clearance due to differences in the trigger mechanism. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. Some plastic stocked models will require you to purchase additional parts from the Accessories page, SAVAGE SA PLASTIC MAG WELL, part no. A09161 or SAVAGE SA METAL MAG WELL, Part No. A09212.. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, YUGOSLAVIAN MAUSER 47, #1 BARREL CONTOUR, FINISHED Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 51/64" and Point B = 51/64" Center to Center of Action Screws: 2 45/64" Over All Length of Part: 28 1/4" w/pad Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: THIS INLET IS BASED ON THE PRE-2022 SOLID STEEL RECEIVER MODELS. NEW MODELS WILL HAVE A PLASTIC CAP ON THE REAR OF THE RECEIVER AND ARE NOT COMPATIBLE. ATTENTION CUSTOMERS: We will provide the trigger guard with two screws. You will need the take down screws and magazine plate from the original stock. ATTENTION CUSTOMERS: If the floor plate from your factory stock is not removeable, you will need the purchase a new floorplate from DIProducts(Sav-13069). Due to variations in floorplates it may require removal of material for a flush fit. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, STEVENS® 315 YOUTH .51 LR, CLIP FEED, LEFT HAND ACTION, BULL BARREL CHANNEL Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 31" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SAVAGE 116, AT-ONE THUMBHOLE, TOP BOLT RELEASE, DETACHABLE MAGAZINE, LONG ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE, YUGOSLAVIAN MAUSER 24, #1 BARREL CONTOUR Barrel Dimensions: Point A = 1 3/8" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS:This stock is designed to accept #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 55/64" and Point B = 51/64" Center to Center of Action Screws: 6" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect . ATTENTION CUSTOMERS :To assemble you will need to use the two escutcheons and action screws from the original.

AT-ONE THUMBHOLE STEVENS® 315 YOUTH .22 LR, BULL BARREL CHANNEL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.