Gunstocks

SPIKE CAMP CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND HERITAGE CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PLATINUM CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PRAIRIE HUNTER CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND FEATHERWEIGHT THUMBHOLE CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND CLASSIC CZ 600 Range Medium Action, Right Hand Action, Left Hand Stock: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND HERITAGE CZ 600 Range Long Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PLATINUM CZ 600 Range Long Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE CZ 600 Range Long Action:Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PRAIRIE HUNTER CZ 600 Range Long Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND FEATHERWEIGHT THUMBHOLE CZ 600 Range Long Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND CLASSIC CZ 600 Range Long Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC CZ 600 Range Long Action: Center to Center of Action Screws: 5 1/2" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver. ATTN Customers: torque settings for the takedown screws is 25 to 35 inch lbs, over torquing could cause damage to teh front magazine tab and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws, and factory front magazine tab.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

SPIKE CAMP CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE THUMBHOLE CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AT-ONE CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND HERT CZ 600 Range Mini Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PLAT CZ 600 Range Mini Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

HERITAGE CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PLATINUM CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND PRAIRIE HUNTER CZ 600 Range Mini Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

VARMINT THUMBHOLE CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND FEATERWEIGHT THUMBHOLE CZ 600 Range Mini Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

FEATHERWEIGHT THUMBHOLE CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

LEFT HAND CLASSIC CZ 600 Range Mini Action, Left Hand Stock, Right Hand Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC CZ 600 Range Mini Action: Center to Center of Action Screws: 4 5/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN customer: torque settings for the takedown screws is 25 to 35 inc lbs, over torquing could cause damage to teh front magzine tab insert and stock. We will provide the trigger guard and front lug plate, you will use the factory takedown screws and Factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

AGILITY CZ 600 Range Medium Action: Center to Center of Action Screws: 5" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety and Bolt Release are located on the side of the receiver.ATTN Customers torque settings for the takedown screws is 25 to 35 inch lbs, over torquing may cause damage to the front magazine tab and stock. We will provide the trigger guard and front lug plate, you will used the factory takedown screws, and factory front magazine tab. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:These stocks are designed for the Winchester Model 70 Long Action No floor plate with standard factory tapered barrel.

Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS :This stock will not work for the WSSM caliber rifles. Pre-1984 actions are based on the Long Action Receiver. These stocks are designed for the Winchester Model 70 Short Action no floorplate model, with standard factory barrel contour. Due to changes made by Winchester to magazine sleeves for short action calibers. Magazine wells that are taller than 1.220 in rear and 1.030 in front will need to be modified to fit Boyds' stocks.

PRO VARMINT, SAKO® QUAD PO4R BOLT, SHORT ACTION, CLIP FED, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 0.911" and Point B = .696"Center to Center of Action Screws: 3.619" Over All Length of Part: 31.25"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need trigger guard and take down screws from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, SAKO® 75-1 HUNTER, SHORT ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1.042" and Point B = .707"Center to Center of Action Screws: 6.683" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and mag box from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1.044" and Point B = .710"Center to Center of Action Screws: 6.235" Over All Length of Part: 27"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, mag box and take down screws from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 15/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Width of Magazine Well: 1 5/16" Length of Magazine Well: 3 11/32" Over All Length of Part: 30.375" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 Bolt Action 17 HMR. Early plastic stocks will require additional mounting hardware to use our stocks. Please contact Ruger or Brownells (800) 741-0015 for the metal trigger guard and clip assembly. This stock can be used with the .17 Hornet caliber along wtih 17 HMR. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 700, LONG ACTION SENDERO, 1 PC HINGED FLOOR PLATE, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1.230" and Point B = .905"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the take down screws, mag well and floorplate from your factory barrel.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, RUGER 77/22®, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 15/16" and Point B = 3/4" Center to Center of Action Screws: 7 1/2" Over All Length of Part: 30" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed for the Ruger 77 Bolt Action 22 Long Rifle. Early plastic stocks will require additional mounting hardware to use our stocks. Please contact Ruger or Brownells (800) 741-0015 for the metal trigger guard and clip assembly. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 770, SHORT ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions:where barrel meets receiver/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 different types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 710, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions:where barrel meets reciever/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 diffrent types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.:All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT REMINGTON® 541-T BOLT, CLIP FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 0.821" and Point B = .821"Center to Center of Action Screws: 3.48" Over All Length of Part: 27.00"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need floor plate, take down screws, and trigger guard from the factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 770, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions:where barrel meets receiver/Point A = 1.230"Barrel Dimensions:9 inches in front of Point A/Point B = .770"Center to Center of Action Screws: (Rear to Mid) 6.935", (Mid to Front 1.75"There are three takedown screws in this gun. Over All Length of Part: 31"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Attention Customers - We will provide trigger guard with screws, 2 escutcheons - 2 different types, rear mag tab, mag clip retainer, take down screw with washer, lug, and instruction sheet.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT, REMINGTON® 700 MOUNTAIN, LONG ACTION, DETACHABLE BOX MAGAZINE, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 1.195" and Point B = 0.606"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.4375"Comes with Boyds' 1/2" Rubber Recoil Pad. Barrel contour for the light weight "Mountain" version.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, PERUVIAN MAUSER 1909, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, PERSIAN MAUSER 98, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, PARKER HALE MAUSER 1200, #1 BC Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, PERUVIAN MAUSER 1935, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Classic Mauser, Large Ring, #1 Barrel Channel, Finished Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

PRAIRIE HUNTER, MAUSER, SMALL RING, MILITARY BARREL CHANNEL Barrel Dimensions: Point A = 1" and Point B = 13/16" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 1/4" Overall Length of Floor Plate: 8 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the military stepped barrel without rear sight sleeve. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All unfinished parts have been CNC inlet to Boyds' House Action. Final sanding and finish will be required. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER, MAUSER LR, MILITARY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 1/8" and Point B = 13/16" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the military stepped barrel minus sight sleeve. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All unfinished parts have been CNC inlet to Boyds' House Action. Final sanding and finish will be required. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, MAUSER LR, MILITARY BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 1/8" and Point B = 13/16" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the military stepped barrel minus sight sleeve. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All unfinished parts have been CNC inlet to Boyds' House Action. Final sanding and finish will be required. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, MAUSER, SMALL RING, # 1 BARREL CHANNEL, LH STOCK, RH ACTION Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 1/4" Overall Length of Floor Plate: 8 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All unfinished parts have been CNC inlet to Boyds' House Action. Final sanding and finish will be required. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, MAUSER, SMALL RING, # 1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 5/8" Front Receiver Ring: 1 1/4" Overall Length of Floor Plate: 8 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All unfinished parts have been CNC inlet to Boyds' House Action. Final sanding and finish will be required. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, MARLIN MAUSER 455, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, JC HIGGINS MAUSER 51, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC HERTERS MAUSER LR, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

CLASSIC, HUSQVARNA MAUSER LR, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, GOLDEN STATE MAUSER, LR, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC FN MAUSER 400, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, CZECH MAUSER LR, #1 BARREL CHANNEL, FINISHED Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC COSTA RICA MAUSER 1910, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC CHARLES DALY MAUSER MARK X, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC CENTURION FN MAUSER, #1 BARREL CHANNEL, ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect .

CLASSIC BRNO MAUSER VZ-24 #1 BARREL CHANNEL ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRAIRIE HUNTER BRNO MAUSER LARGE RING #1 BARREL CHANNEL ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC BRNO MAUSER #1 BARREL CHANNEL ZZ Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

ARGENTINE MAUSER 1909, CLASSIC, #1 BC Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 9/64" and Point B = 45/64" Center to Center of Action Screws: 7" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and the Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : Steel lug will be furnished with the stock. Ensure proper installation of the lug during assembly. ATTENTION CUSTOMERS: This stock is compatible with the T3x model. ATTENTION CUSTOMERS: This stock is NOT compatible with the T3x Compact Tactical.***Aluminum T3 Bottom Metal available on the Accessories page. Compatible with T3 and T3 Lite models. Part number: A09210*** It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST ZASTAVA® M70 BOLT LA HINGED FP FBC Barrel Dimensions: Point A = 1 1/8" and Point B = 11/16"Center to Center of Action Screws: 7 13/16"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

Barrel Dimensions: Point A = 1 1/8" and Point B = 11/16"Center to Center of Action Screws: 7 13/16" Over All Length of Part: 29 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the floor plate and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CZ 527 AMERICAN, QUEST, DETACHABLE BOX MAGAZINE, SHORT ACTION, FACTORY BARREL CHANNEL Barrel Dimensions: Point A = 63/64" and Point B = 45/64" Center to Center of Action Screws: 5 1/2" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION: THIS STOCK IS NOT COMPATIBLE WITH THE CZ 527 M CARBINE MODEL. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CZ® 455, QUEST, CLIP FEED, BULL BARREL CHANNEL Barrel Dimensions: Point A = 15/16" and Point B = 15/16" Center to Center of Action Screws: 6 1/8" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed using the 455 heavy barrel or bull barrel and we use an inlet trigger guard and floor plate. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect."

CZ® 452 .22LR, QUEST, BULL BARREL CHANNEL Barrel Dimensions: Point A = 1 1/16" and Point B = 15/16" Center to Center of Action Screws: 6 1/8" Over All Length of Part: 29.25" Comes with Boyds' 1/2" Rubber Recoil Pad It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: These stocks are designed using metal trigger guard and floor plate and are made using barrel mounting screw model. If your action has rear receiver mounting screw please review Mag parts (if available). All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, HOWA 1500, SHORT ACTION, BULL BARREL CHANNEL, ZZ, FINISHED Barrel Dimensions: Point A = 1 1/4" and Point B = 1" Center to Center of Action Screws: 7 1/4" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

DEFIANCE: CLASSIC, MEDIUM ACTION, STANDARD TANG, DBM HAWKINS PRECISION M5 BOTTOM METAL HEAVY BARREL CHANNEL Barrel Channel Dimensions: Point A - 1 1/4" Point B - 7/8" Center to Center Action Screws: 6 3/4" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Medium Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

DEFIANCE: CLASSIC, MEDIUM ACTION, STANDARD TANG, DBM HAWKINS PRECISION M5 BOTTOM METAL HEAVY BARREL CHANNEL Barrel Channel Dimensions: Point A - 1 1/4" Point B - 7/8" Center to Center Action Screws: 6 3/4" Comes with Boyds 1/2" recoil pad. ATTENTION CUSTOMERS: This inlet is machined to accept the Hawkins Precision M5 Detachable Box Magazine Medium Action Bottom Metal. You will need to purchase the Hawkins Precision M5 Bottom Metal separately. Inlet is not milled for Hawkins pillars due to end user preference. Refer to Hawkins Precision for specifics of the M5 Detachable Box Magazine. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

PRO VARMINT RUGER® MINI 30 Barrel Dimensions: Point A = 29/32" and Point B = 5/8"Over All Length of Part: 29 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need the factory trigger assembly, magazine, forend liner, and cap assembly from your original stock. Our inlet is designed not to use the stock reinforcement or side stock reinforcement screws. There will not be swivel studs installed on the forend.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

CLASSIC, MAUSER LR, #1 BARREL CHANNEL Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.

QUEST, SAVAGE® 93E MKII, BULL BARREL CHANNEL STOCK, FINISHED Barrel Dimensions: Point A = 13/16" and Point B = 13/16" Center to Center of Action Screws: 3 11/16" Over All Length of Part: 29 1/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Sav93-E/MKII heavy barrel with inlet trigger guard and floor plate. Action measures 7 3/4" long on the 93E/MKII action. Pre-93E receivers (with a lug at the back of the reciever) can be fit to our 93E/MKII stocks but will require fitting of your receiver and barrel to the stock. Minor gap will be visible on rear of stock with older pre-accutrigger actions. Older receivers are about 4 inches longer and will need to be fit. Variations in action mounting screw pillars exist between models. Do not over tighten. ATTN customers: Side mount rear peep sights will require modifications of the stock for fitment. All plastic stocks, and some laminate and hardwood stocks will require you to purchase a different trigger guard and floor plate. You can purchase them on the Accessories page, bottom left-hand corner. Part numbers for 22 LR: 100654 (Blued), 100655 (Nickel). Part numbers for 17hmr/22mag: 100656 (Blued), 100657 (Nickel). Some stocks may also require different action screws which are available through DiProductsInc: PN 13020. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.