Rapid Fire Products

HERT RUGER AMERICAN SHORT ACTION DBM FBC Coyote Satin Finish Boyds Pad Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP Savage B-mag Dbm Sa Bull Barrel Channel Forest Camo Satin Finish Boyds Pad Barrel Dimensions: Point A = 55/64" and Point B = 51/64" Center to Center of Action Screws: 6" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. Safety is located on the tang and Bolt Release is on the side of the receiver. ATTENTION CUSTOMERS : To assemble, you will need to use the two escutcheons and action screws from the original. The trigger guard/floor plate from original stock is not needed. We will provide you with a black plastic trigger guard. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect . ATTENTION CUSTOMERS :To assemble you will need to use the two escutcheons and action screws from the original. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

FT BROWNING A-BOLT LONG ACTION FBC FOREST CAMO SATIN FINISH LIMBSAVER PAD ANGLED WALNUT TIP CAP LASER PANEL PILLAR BEDDING LOP 14 1/4" BROWNING® A-BOLT LONG ACTION FACTORY BARREL CHANNEL ZZ Barrel Dimensions: Point A = 1 1/4" and Point B = 13/16" Center to Center of Action Screws: 8" Over All Length of Part: 31/1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info. All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect All Rapid Fire sales are final! Nonreturnable & nonrefundable. pan>

HERT RUGER AMERICAN SHORT ACTION DBM FBC Royal Satin Finish Boyds Pad ATTENTION CUSTOMERS: SCRATCH ON LEFT SIDE OF GRIP Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks will provide the required bedding compound and you must bed the front and rear lugs. ATTENTION CUSTOMERS : Does not work with AR Mags. ATTENTION CUSTOMERS: Compatible with AI magazines if used with the Ruger American AI Magazine Kit (part no. A09158) offered on the Accessories page. See full list of compatible short action calibers here: https://www.boydsgunstocks.com/ruger-american-ai-magazine. ATTENTION: This inlet is compatible with the 7.62x39 caliber using Mini 30 magazines, in conjuction with the RUGER AMERICAN 7.62X39 CALIBER MAGAZINE KIT (part no. A09217) offered on the Accessories page. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

RIMFIRE HUNTER RUGER 1022 CARBINE BARREL CHANNEL WALNUT SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: CHIP IN THE TIP INLET AND CHIP ON TOP OF INLET DOWN THE LEFT HAND SIDE OF BARREL CHANNEL Barrel Dimensions: Point A = 59/64" and Point B = 43/64"Center to Center of Action Screws: N/AOver All Length of Part: 31 1/4"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock comes with brass mounting escutcheon installed and is designed for the Factory Ruger 10/22 Semi-Auto Action, measuring 6 3/16" long.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

MARLIN 336 PISTOL GRIP STOCK AND CAP STYLE FOREND NUTMEG SATIN FINISH BOYDS BUTT PLATE FOREND It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Channel Point A: 15/16"Barrel Channel Point B: 13/16"Magazine Tube Width: 3/4"Magazine Tube Shoulder to Shoulder: 9 1/4"Over All Length of Part: 9 9/16"All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS:There are a few variations of Cap style forends that were made for this model. Please confirm dimensions prior to ordering. STOCK Length of Pull 13 3/4"Top Tang width 1/2"Top Tang length 3 1/16"BottomTang width 9/16"BottomTang length 3 1/8 "Stock height at receiver 1 3/4 "Stock width at receiver 1 1/2 " All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Nutmeg ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Pepper ATTENTION CUSTOMERS: 10 1/2" factory stock bolt is required for this buttstock. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 10 1/2"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

AMERICAN PLAINSMAN REMINGTON 870 12GA STOCK Walnut It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: You will need to purchase the 8 5/16" mounting bolt for wood stocks from the Accessories page, Part Number: A09168.Top Tang Width: N/ATop Tang Length: N/ABottom Tang Width: 1/2"Bottom Tang Length: 5/8"Stock Height at Receiver: 1 15/16"Stock Width at Receiver: 1 1/2"Overall Length of Stock: 13 3/4"Measurement of Receiver Mounting Bolt - 8 5/16"Comes with Pachmay Decelerator recoil padAll finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect.ATTENTION CUSTOMERS: These stocks are designed for the larger frame models. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PH CZ 550 AMERICAN LONG ACTION FBC PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: FINISH FLAWS AND DENTS ON COMB It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.   Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64" Center to Center of Action Screws: 7 53/64” Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

FT WIN 70 PRE-64 LA 2PC FP FBC Black Jack Satin Finish Limbsaver Pad Laser Symbol: Wolf Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4" Center to Center of Action Screws: 7 7/16" Over All Length of Part: N/A Comes with Boyds' 1/2" Rubber Recoil Pad. ATTENTION CUSTOMERS: These stocks are designed for the Winchester model 70 pre 64 long action, with a 2 piece floor plate, factory barrel. You will need your factory Trigger Guard, 2-Piece Hinged Floor Plate, 3 Action Screws, Machine Screw w/escutcheon(Forend Location) & Magazine Box. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLAT REM 700 LA 1PC FP LH STOCK RH ACT BBC Walnut Satin Finish Pachmayr Pad Laser Panel Pillar Bedding Barrel Dimensions: Point A = 1.245" and Point B = 0.9"Center to Center of Action Screws: 7.345" Over All Length of Part: 31.5"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS:You will need the floor plate, mag box, and take down screws from your factory stock.All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PLAT REM 700 ADL LA FBC CLARO XX WALNUT SATIN FINISH LIMBSAVER PAD WHITE LINE SPACER ANGLED WALNUT TIP CAP WALNUT GRIP CAP LASER PANEL PILLAR BEDDING Barrel Dimensions: Point A = 1 1/4" and Point B = 25/32" Center to Center of Action Screws: 7 3/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: Inlett for standard factory tapered barrel channel. This stock is designed for the Remington 700 Right Hand Long Action with blind magazine, loads and unloads through top of action. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP THUMBHOLE RUGER AMERICAN CENTERFIRE LONG ACTION DBM FBC FOREST CAMO SATIN FINISH 1" KICK-EEZ PAD ATTENTION CUSTOMERS: TOP OF PAD SPACER IS CHIPPED/GOUGED Barrel Dimensions: Point A = 1 5/32" and Point B = 23/32" Center to Center of Action Screws: 4 37/64" Over All Length of Part: 29 3/4" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: We will provide the front and rear lugs, front and rear takedown screws, trigger guard with screw, and the front magazine tab catch. Boyds Gunstocks recommends bedding the front and rear lugs.Long Action Calibers: 270 Win, 30-06 Spfld.ATTENTION CUSTOMERS : Does not work with AI or AR Mags. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

Savage® 67 (top Rec Safety) Stock WALNUT UNFINISH BOYDS BUTTPLATE These parts are designed to fit the Savage,Stevens,Springfield and Fox models 30,67,77,79,168 and 176 stocks with top receiver safety, please compare your stock and receiver measurements with those we supply.Make sure to confirm demensions with those supplied for this parts. There may be up to five variations of this model.Top Tang width - 9/16ths"Top Tang length - 1 7/16ths"BottomTang width - 5/8ths"BottomTang length - 1 5/16ths"Stock height at receiver -1 5/8ths"Stock width at receiver -1 1/2" Semi-inlet parts have been comletely shaped and 95% machine inlet. Stocks are rough sanded and unless otherwise specified, are shipped with a BOYDS' butt plate.(SEMI-INLET) stocks do require some knowledge of firearms and woodworking for installation. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

LH STERLING THUMBHOLE H&R® SINGLE SHOT STOCK & FOREND APPLE JACK SATIN FINISH BOYDS VENTED PAD STOCK Stock comes with mounting bolt that will require 7/32 allen wrench for assembly. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Top Tang Width: N/A Top Tang Length: N/A Bottom Tang Width: N/A Bottom Tang Length: N/A Stock Height at Receiver: 1 3/4" Stock Width at Receiver: 1 15/32" Overall Length of Stock: 12 3/4" Comes with 3/4" vented recoil pad All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS: These stocks are designed for the modern style knuckle style receiver. Please see our H&R round tang stock for older tanged receiver models. FORENDIt is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. Barrel Channel Point A: 1 1/16 " Barrel Channel Point B: 11/16 " Receiver Edge to Center of Mounting Screw: 3 5/8 " Center to Center of Mounting Screws/Magazine Tube Shoulder to Shoulder: N/A" Over All Length of Part: 9 " All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. ATTENTION CUSTOMERS:If you are converting from a plastic forend, you will need to purchase rear mounting bracket from H&R or Brownells.These parts require fitting of your barrel. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH MAUSER LARGE RING #1 BARREL CHANNEL XX MAPLE HIGH GLOSS BLACK TIP BLACK GRIP CAP BOYDS PAD LOP 14" ATTENTION CUSTOMERS: TIP IS SEVERELY SCRATCHED AND A CHIP IN THE FINISH. GRIP HAS PEELING FINISH. SANDING MARKS THROUGHOUT STOCK. Barrel Dimensions: Point A = 1 3/16" and Point B = 7/8" Center to Center of Action Screws: 7 7/8" Front Receiver Ring: 1 3/8" Overall Length of Floor Plate: 8 11/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed to accept the #1 Sporter Contour barrel. Due to the numerous variations of hardware used on these actions, we have not cut a bolt cut or safety cut in our stock and final fitting of floor plate may be required. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

PLAT WIN 70 SHORT ACT 2PC FP FBC POST 64 PEPPER SATIN FINISH BOYDS PAD ATTENTION CUSTOMERS: OVERSANDING ON TIP, ONE SIDE DROPS OFF MAKING IT UNEVEN Barrel Dimensions: Point A = 1 3/16" and Point B = 13/16" Center to Center of Action Screws: 7 1/8" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock will not work for the WSSM Caliber Rifles. Pre-1984 actions are based on the Long Action receiver. These stocks are designed for the Winchester? Model 70 Short Action 2-Piece hinged floor plate model with a standard factory tapered barrel. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect./p> All Rapid Fire sales are final! Nonrefundable & nonreturnable.

HERT SAV 10 TBR BLIND MAGAZINE, SHORT ACTION, LEFT HAND STOCK, RIGHT HAND ACT, CENTERFEED, FACTORY BARREL CHANNEL NUTMEG SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: New action screws are needed if your action screws are shorter than 1 1/4 and 1 1/2 respectively. These are sold separately on our Accessories page. This stock is designed for the Savage Blind Magazine with Center Feed Action and a top bolt release. When you disassemble your action the magazine box will stay inside the stock when the barreled action is removed. If the magazine box stays attached to the action, you may need the Staggered Feed Model or STAGGERED FEED version we offer. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final!

PH CZ 550 AMERICAN LONG ACTION FBC PEPPER SATIN FINISH BOYDS PAD It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.Barrel Dimensions: Point A = 1 7/64" and Point B = 47/64"Center to Center of Action Screws: 7 53/64”Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.ATTENTION CUSTOMERS:  You will need your takedown screws, floor plate assembly, and mag well. All finished stocks have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

SPIKE CAMP THUMBHOLE SAV 10 TBR SHORT ACTION DETACHABLE MAG FBC MAROON SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 4 7/16" Over All Length of Part: 29 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Short Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS: If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE SA PLASTIC MAG WELL from our Accessories page, Part No. A09161. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

CLA SAV 111 TBR DETACHABLE MAG LONG ACTION FBC PEPPER SATIN FINISH PACHMAYR PAD LASER PANEL BLACK GRIP CAP PILLAR BEDDING ATTENTION CUSTOMERS: DISCOLORATION IN LASER PANEL ON FOREND, BROWN Barrel Dimensions: Point A = 1 5/16" and Point B = 3/4" Center to Center of Action Screws: 5 1/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: This stock is designed for the Savage detachable box magazine rifle with top bolt release. The magazine release is located on the bottom of the floorplate. Not designed for old style side magazine release. Due to the many variations of trigger guards that have bed used for Savage Actions. Boyds uses a flat bottom metal design. Fitting for plastic and some metal models may be needed or contact Savage or Brownells for the flat bottom design. This stock is designed for the Savage Long Action Detachable Box Magazine rifles with top bolt release. The magazine release is located on the bottom of the floorplate. These stocks are designed for the 3 piece design DETACHABLE BOX MAG parts as found on wood stocks. ATTENTION CUSTOMERS:If you have a XP model with a synthetic stock, you will need to purchase the SAVAGE LA PLASTIC MAG WELL from our Accessories page, Part No. A09160 or SAVAGE LA METAL MAG WELL, Part No. A09213. Not designed for old style side magazine release. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

SPIKE CAMP THUMBHOLE RUGER ACF PREDATOR AR MAG SA FBC FOREST CAMO SATIN FINISH BOYDS PAD Barrel Dimensions: Point A = 1 1/64" and Point B = 3/4" Center to Center of Action Screws: 4 3/64" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS : We will provide the Ruger American AR magazine conversion floor plate, front and rear lugs, front and rear taked down screws, trigger guard with screw, magazine release catch, magazine release spring, magazine release button. Boyds Gunstocks recommends bedding the front and rear lugs.. ATTENTION: A relief cut to allow magazine release button clearance has been added. ATTENTION CUSTOMERS : You will need round specific magazines for the 7.62x39, 300 Blackout, 350 legend, and 6.5 grendel. Due to dimmensional differences they will not feed or stack properly in a standard 5.56 magazine. Calibers that are not compatible include: .308, 6.5 Creedmoor, and .243. Calibers that are compatible without round specific magazines: .223 and .204. ATTENTION: The Ruger American Trigger Guard set found on our Accessories page is not compatible with the AR Magazine gunstock. ATTENTION: This stock is not compatible with the Ruger Mini 30 Magazines due to the steel mag liner. ATTENTION: This stock is not compatible with Ruger Mini 30 magazines due to magazine dimensional differences. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.

PH BROWNING A-BOLT SHORT ACT FBC NUTMEG HIGH GLOSS BOYDS PAD ANGLED BLACK TIP BLACK GRIP CAP LASER INITIALS: LEA FONT #2 Barrel Dimensions: Point A = 1 1/4" and Point B = 3/4"Center to Center of Action Screws: 7 1/4"Over All Length of Part: 31 1/2"Comes with Boyds' 1/2" Rubber Recoil Pad.It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part.ATTENTION CUSTOMERS: Before you order, you must confirm, by Serial Number, if your firearm model is an A-Bolt, A-Bolt II or A-Bolt III. The roll stamping on all versions only states A-Bolt, regardless of model. Also confirm if your particular firearm is a MICRO version or not. MICRO versions are different than the standard models. Check out Browning for more info.All finished stocks have been CNC inlet to Boyds House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm.Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonreturnable & nonrefundable.

HERITAGE MOSSBERG 100 ATR SA FBC XX MAPLE HIGH GLOSS WHITE LINE SPACER BOYDS PAD BLACK GRIP CAP LASER PANEL ATTENTION CUSTOMERS: Visible sanding marks throughout stock. Slight dent on comb. Barrel Dimensions: Point A = 1 3/8" and Point B = 13/16" Center to Center of Action Screws: 4 9/16" Over All Length of Part: 31 1/2" Comes with Boyds' 1/2" Rubber Recoil Pad. It is your responsibility to confirm the dimensions of your firearm with the supplied dimensions of our part. ATTENTION CUSTOMERS: If you are converting from a plastic stock, you will need to purchase a trigger guard from our Accessories page: ITEM # A09157, and an action screw from Mossberg directly, ITEM # 101532. All finished parts have been CNC inlet to Boyds' House Action. Variations may exist from firearm to firearm, minor fitting may be required to get that perfect fit to your firearm. Natural cosmetic imperfections such as minor knots, burls, heartwood, mineral lines or minor cosmetic fill work are not considered a defect. All Rapid Fire sales are final! Nonrefundable & nonreturnable.